Nessuna risorsa pertinente trovata nella lingua selezionata.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S7700 and S9700 V200R011C10

This document describes the configuration of BFD, DLDP, VRRP, SmartLink, CFM, EFM, Y.1731 and MAC swap loopback to ensure reliability on the device.
Rate and give feedback:
Huawei utilizza la traduzione automatica insieme alla revisione umana per tradurre questo documento in diverse lingue, per facilitare la comprensione del contenuto di questo documento. Nota: la traduzione automatica, anche la più avanzata, non può corrispondere alla qualità dei trasduttori professionisti. Huawei non accetta alcuna responsabilità per l'accuratezza della traduzione e raccomanda di fare riferimento al documento inglese (per il quale è stato fornito un collegamento).
Configuring Two-way Frame Delay Measurement

Configuring Two-way Frame Delay Measurement

Context

  • To measure the two-way frame delay at a time or a specific number of times, use the on-demand mode.

  • To measure the two-way frame delay periodically, use the proactive mode.

Procedure

  • Configure on-demand two-way frame delay measurement.

    1. Perform the following operations on the MEP and RMEP.

      1. Run system-view

        The system view is displayed.

      2. Run cfm md md-name

        The MD view is displayed.

      3. Run ma ma-name

        The MA view is displayed.

      4. Run map vlan vlan-id

        The MA is bound to a VLAN.

      5. Run mep mep-id mep-id interface interface-type interface-number [ pe-vid pe-vid ce-vid ce-vid ] { inward | outward }

        The MEP is configured.

      6. Run remote-mep mep-id mep-id [ mac mac-address ]

        The remote MEP ID is configured.

      7. Run mep ccm-send [ mep-id mep-id ] enable

        The CCM transmission function is enabled.

      8. Run remote-mep ccm-receive [ mep-id mep-id ] enable

        The CCM reception function is enabled.

      9. (Optional) Run delay-measure two-way threshold threshold-value

        The alarm threshold for two-way frame delay measurement is set.

    2. On the receiver RMEP, run:delay-measure two-way receive mep mep-id

      The RMEP is enabled to receive DMMs.

      By default, the RMEP in an MA is not enabled to receive DMMs.

    3. On the initiator MEP, run:delay-measure two-way send mep mep-id { mac mac-address | remote-mep mep-id } interval { 1000 | 10000 } count count-value

      On-demand two-way frame delay measurement is configured.

      VLAN-specific two-way frame delay measurement is implemented based on an RMEP ID or destination MAC address:
      • If the local MEP has not learnt the MAC address of the RMEP, specify the RMEP destination MAC address before implementing two-way frame delay measurement.

      • If the local MEP has learnt the MAC address of the RMEP, specify the RMEP ID before implementing two-way frame delay measurement.

  • Configure proactive two-way frame delay measurement.

    1. Perform the following operations on the MEP and RMEP.

      1. Run system-view

        The system view is displayed.

      2. Run cfm md md-name

        The MD view is displayed.

      3. Run ma ma-name

        The MA view is displayed.

      4. Run map vlan vlan-id

        The MA is bound to a VLAN.

      5. Run mep mep-id mep-id interface interface-type interface-number [ pe-vid pe-vid ce-vid ce-vid ] { inward | outward }

        The MEP is configured.

      6. Run remote-mep mep-id mep-id [ mac mac-address ]

        The remote MEP ID is configured.

      7. Run mep ccm-send [ mep-id mep-id ] enable

        The CCM transmission function is enabled.

      8. Run remote-mep ccm-receive [ mep-id mep-id ] enable

        The CCM reception function is enabled.

      9. (Optional) Run delay-measure two-way threshold threshold-value

        The alarm threshold for two-way frame delay measurement is set.

    2. On the receiver RMEP, run:delay-measure two-way receive mep mep-id

      The RMEP is enabled to receive DMMs.

      By default, the RMEP in an MA is not enabled to receive DMMs.

    3. On the initiator MEP, run:delay-measure two-way continual send mep mep-id { mac mac-address | remote-mep mep-id } interval 30000

      Proactive two-way frame delay measurement is configured.

      By default, proactive two-way frame delay measurement is not configured in an MA.

      VLAN-specific two-way frame delay measurement is implemented based on an RMEP ID or destination MAC address:
      • If the local MEP has not learnt the MAC address of the RMEP, specify the RMEP destination MAC address before implementing two-way frame delay measurement.

      • If the local MEP has learnt the MAC address of the RMEP, specify the RMEP ID before implementing two-way frame delay measurement.

Traduzione
Download
Updated: 2019-09-23

N. documento: EDOC1000178318

Visualizzazioni:123843

Download: 81

Average rating:
This Document Applies to these Products
Documenti correlati
Related Version
Share
Precedente Avanti