Nessuna risorsa pertinente trovata nella lingua selezionata.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S7700 and S9700 V200R011C10

This document describes the configuration of BFD, DLDP, VRRP, SmartLink, CFM, EFM, Y.1731 and MAC swap loopback to ensure reliability on the device.
Rate and give feedback:
Huawei utilizza la traduzione automatica insieme alla revisione umana per tradurre questo documento in diverse lingue, per facilitare la comprensione del contenuto di questo documento. Nota: la traduzione automatica, anche la più avanzata, non può corrispondere alla qualità dei trasduttori professionisti. Huawei non accetta alcuna responsabilità per l'accuratezza della traduzione e raccomanda di fare riferimento al documento inglese (per il quale è stato fornito un collegamento).
Association Between VRRP and BFD

Association Between VRRP and BFD

A VRRP group sends and receives VRRP Advertisement packets to determine the master and backup statuses, thereby implementing redundancy. If links connected to a VRRP group fail, VRRP Advertisement packets cannot be sent for negotiation. A backup will switch to the master after three times the duration of the interval (about 3s) at which point VRRP Advertisement packets are sent. During the switchover period, service traffic is still sent to the original master, causing user traffic loss.

BFD can rapidly detect connectivity of links on the network. Association between VRRP and BFD implements a fast switchover within 1 second. A BFD session is set up between the master and backup and is bound to a VRRP group. BFD detects faults of the VRRP group. When a fault occurs, BFD notifies the VRRP group of performing an active/standby switchover, greatly reducing the service interruption time.

A VRRP group can be associated with a static BFD session or a BFD session with automatically negotiated parameters.

There are two modes of association between VRRP and BFD. Table 3-3 describes the differences between the two modes.

Table 3-3  Two modes of association between VRRP and BFD

Association Mode

Usage Scenario

Impact

Device Setting

Common mode

The backup detects whether the master works properly. The BFD session is often used to monitor the status of the link between the master and backup.

The VRRP group adjusts its priority according to the BFD session status and determines whether to perform an active/standby switchover according to the adjusted priority.

The device configured with VRRP must support BFD.

Peer mode

The backup detects whether the master works properly. The BFD session is often used to monitor the status of the link between the master and backup.

When the peer BFD session status changes, the VRRP device's priority remains unchanged and the VRRP group status is reconfigured.

The device configured with VRRP must support BFD.

Figure 3-8  Association between VRRP and BFD

As shown in Figure 3-8, a VRRP group is configured between SwitchA and SwitchB. SwitchA is the master and SwitchB is the backup. User traffic is forwarded through SwitchA. SwitchA and SwitchB work in preemption mode, and immediate preemption is configured on SwitchB. BFD sessions are configured on SwitchA and SwitchB and association between VRRP and BFD is configured on SwitchB.

When a fault occurs in the VRRP group, BFD rapidly detects the fault and instructs SwitchB to increase the priority to a value higher than that of SwitchA. SwitchB immediately switches to the master and forwards user-side traffic, implementing a rapid active/standby switchover.

Traduzione
Download
Updated: 2019-10-18

N. documento: EDOC1000178318

Visualizzazioni:124610

Download: 81

Average rating:
This Document Applies to these Products
Documenti correlati
Related Version
Share
Precedente Avanti