Nessuna risorsa pertinente trovata nella lingua selezionata.

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S7700 and S9700 V200R011C10

This document describes the configuration of BFD, DLDP, VRRP, SmartLink, CFM, EFM, Y.1731 and MAC swap loopback to ensure reliability on the device.
Rate and give feedback:
Huawei utilizza la traduzione automatica insieme alla revisione umana per tradurre questo documento in diverse lingue, per facilitare la comprensione del contenuto di questo documento. Nota: la traduzione automatica, anche la più avanzata, non può corrispondere alla qualità dei trasduttori professionisti. Huawei non accetta alcuna responsabilità per l'accuratezza della traduzione e raccomanda di fare riferimento al documento inglese (per il quale è stato fornito un collegamento).
(Optional) Configuring VRRP6 Time Parameters

(Optional) Configuring VRRP6 Time Parameters

Context

You can set VRRP6 time parameters as needed. Table 3-8 lists applicable scenarios.

Table 3-8  Applicable scenarios of VRRP6 time parameters
Function Usage Scenario
Interval at which VRRP6 Advertisement packets are sent The master in a VRRP6 group sends VRRP6 Advertisement packets to backups at intervals to notify that it is working properly. After the Master_Down_Interval timer expires, the backup with the highest priority switches to the master if it does not receive VRRP6 Advertisement packets.

Heavy network traffic or time differences on different devices may result in the status change of the backups due to timeout of VRRP6 Advertisement packets. When packets from the original master reach the new master, the status of the new master changes. You can increase the interval to solve this problem.

Interval at which ND packets are sent by the master To ensure that MAC address entries on the downstream switch are correct, the master in a VRRP6 group periodically sends ND packets to update MAC address entries on the downstream switch.
Delay before a VRRP6 group recovers On an unstable network, frequent flapping of the BFD session status or interface status monitored by a VRRP6 group may result in frequent switching of the VRRP6 group status. After the delay is set, the VRRP6 group does not immediately respond to an interface or BFD session Up event. Instead, the VRRP6 group processes this event after the delay. This prevents frequent switching of the VRRP6 group status.

Procedure

  • Set the interval at which VRRP6 Advertisement packets are sent.
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The interface view is displayed.

    3. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    4. Run vrrp6 vrid virtual-router-id timer advertise advertise-interval

      The interval at which VRRP6 Advertisement packets are sent is set.

      By default, VRRP6 Advertisement packets are sent at intervals of 1s.

      NOTE:

      If devices in a VRRP6 group use different intervals, VRRP6 may not work.

  • Set the interval at which ND packets are sent by the master.
    1. Run system-view

      The system view is displayed.

    2. Run vrrp gratuitous-arp timeout time

      The interval at which ND packets are sent by the master is set.

      By default, the master sends ND packets every 120s.

      The interval at which the master sends ND packets must be shorter than the aging time of ND entries on each user device.

      • To restore the default interval at which an ND packet is sent, run the undo vrrp gratuitous-arp timeout command in the system view.

      • To disable the master from sending ND packets, run the vrrp gratuitous-arp timeout disable command in the system view.

  • Set the delay before a VRRP6 group recovers.
    1. Run system-view

      The system view is displayed.

    2. Run vrrp recover-delay delay-value

      The delay before a VRRP6 group recovers is set.

      By default, the delay before a VRRP6 group recovers is 0.

      NOTE:
      • After this command is used, all VRRP6 groups on the device are configured with the same delay.

      • When the device in a VRRP6 group restarts, VRRP6 status flapping may occur. It is recommended that the delay be set based on actual networking.

Traduzione
Download
Updated: 2019-10-18

N. documento: EDOC1000178318

Visualizzazioni:124888

Download: 83

Average rating:
This Document Applies to these Products
Documenti correlati
Related Version
Share
Precedente Avanti