Nessuna risorsa pertinente trovata nella lingua selezionata.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S7700 and S9700 V200R011C10

This document describes the configuration of BFD, DLDP, VRRP, SmartLink, CFM, EFM, Y.1731 and MAC swap loopback to ensure reliability on the device.
Rate and give feedback:
Huawei utilizza la traduzione automatica insieme alla revisione umana per tradurre questo documento in diverse lingue, per facilitare la comprensione del contenuto di questo documento. Nota: la traduzione automatica, anche la più avanzata, non può corrispondere alla qualità dei trasduttori professionisti. Huawei non accetta alcuna responsabilità per l'accuratezza della traduzione e raccomanda di fare riferimento al documento inglese (per il quale è stato fornito un collegamento).
Configuring AIS

Configuring AIS

Context

In Figure 10-10, the MEPs configured on the access interfaces of CE1 and CE2 reside in level-6 MD1. The MEPs configured on PE1 and PE2 reside in level-3 MD2. When a fault occurs, a MEP in level-3 MD2 first detects the fault and sends an alarm to the NMS. After a certain period, a MEP in level-6 MD1 also detects the fault and sends the same alarm to the NMS. Therefore, the AIS function needs to be configured on the PEs to prohibit the MEP in the MD of a higher level from sending alarms to the NMS.
NOTE:

Millisecond-level connectivity check cannot be performed for a link between CEs configured with alarm suppression.

When the device processes many AIS packets, the CPU usage will become high. When the device is enabled with AIS, it is recommended that nestling layers in an MD should be reduced and the number of interfaces associated with VLANs in an MA should be reduced.

Figure 10-10  Configuring AIS in the VLAN

Procedure

  1. Performing the following operations on the PE.

    1. Run system-view

      The system view is displayed.

    2. Run cfm md md-name

      The MD view is displayed.

    3. Run ma ma-name

      The MA view is displayed.

    4. Run map vlan vlan-id

      The MA is bound to a VLAN.

    5. Run ais enable

      AIS is enabled in the MA.

      By default, AIS is disabled.

    6. (Optional) Run ais link-status

      AIS is configured to monitor interfaces in the MA.

      By default, AIS does not monitor any interface.

    7. (Optional) Run ais interval interval-value

      The interval at which AIS PDUs are sent is set.

      By default, the interval at which AIS PDUs are sent is 1s.

      NOTE:

      If the range of VLANs to which AIS PDUs are sent is set, you are advised to set the interval at which AIS PDUs are sent to 60s.

    8. Run ais level level-value

      The level of AIS PDUs to be sent is set.

    9. Run ais vlan { pe-vid pe-vid ce-vid { low-ce-vid [ to hig-ce-vid ] } &<1–10> | vid { low-vid [ to high-vid ] } &<1–10> } mep mep-id

      The range of VLANs to which AIS PDUs are to be sent is set.

  2. Performing the following operations on the CE.

    1. Run system-view

      The system view is displayed.

    2. Run cfm md md-name

      The MD view is displayed.

    3. Run ma ma-name

      The MA view is displayed.

    4. Run map vlan vlan-id

      The MA is bound to a VLAN.

    5. Run ais enable

      AIS is enabled in the MA.

      By default, AIS is disabled.

    6. Run ais suppress-alarm

      Alarm suppression is enabled in the MA.

      By default, alarm suppression is disabled in a MEP.

      In an MD nesting scenario, if alarm suppression is enabled in the MD of a high level, a MEP in this MD does not send alarms that a MEP in an MD of a low level has sent to the NMS after receiving an AIS PDU.

Traduzione
Download
Updated: 2019-09-23

N. documento: EDOC1000178318

Visualizzazioni:124323

Download: 81

Average rating:
This Document Applies to these Products
Documenti correlati
Related Version
Share
Precedente Avanti