所选语种没有对应资源,请选择:

本站点使用Cookies,继续浏览表示您同意我们使用Cookies。Cookies和隐私政策>

提示

尊敬的用户,您的IE浏览器版本过低,为获取更好的浏览体验,请升级您的IE浏览器。

升级

S9300, S9300E, S9300X V200R010C00 配置指南-网络管理与监控

本文档介绍了设备支持的网络管理与监控相关配置。主要内容包括:SNMP配置、RMON和RMON2配置、LLDP配置、性能管理、iPCA配置、NQA配置、业务诊断配置、镜像配置、报文捕获配置、分流配置、NetStream配置、sFlow配置、TWAMP Light配置。
评分并提供意见反馈 :
华为采用机器翻译与人工审校相结合的方式将此文档翻译成不同语言,希望能帮助您更容易理解此文档的内容。 请注意:即使是最好的机器翻译,其准确度也不及专业翻译人员的水平。 华为对于翻译的准确性不承担任何责任,并建议您参考英文文档(已提供链接)。
配置MAC Ping测试示例

配置MAC Ping测试示例

组网需求

图6-40所示。

  • SwitchA和SwitchB上都启用CFM。

  • SwitchA和SwitchB上配置MA和MD。

使用NQA MAC Ping功能测试SwitchA与SwitchB设备之间的连通性状态。

图6-40  MAC Ping测试组网图

配置思路

采用如下思路进行MAC Ping测试的配置:

  1. SwitchA作为NQA客户端。

  2. SwitchB作为NQA服务器端。

  3. SwitchA上建立MAC Ping测试用例。

操作步骤

  1. 配置SwitchA和SwitchB之间的MA和MD

    # 配置SwitchA。

    <Quidway> system-view
    [Quidway] sysname SwitchA
    [SwitchA] vlan batch 11
    [SwitchA] interface gigabitethernet 1/0/1
    [SwitchA-GigabitEthernet1/0/1] port hybrid pvid vlan 11
    [SwitchA-GigabitEthernet1/0/1] port hybrid untagged vlan 11
    [SwitchA-GigabitEthernet1/0/1] quit
    [SwitchA] cfm enable
    [SwitchA] cfm md test
    [SwitchA-md-test] ma test
    [SwitchA-md-test-ma-test] map vlan 11
    [SwitchA-md-test-ma-test] mep mep-id 11 interface gigabitethernet1/0/1 outward
    [SwitchA-md-test-ma-test] mep ccm-send mep-id 11 enable
    [SwitchA-md-test-ma-test] remote-mep mep-id 12
    [SwitchA-md-test-ma-test] remote-mep ccm-receive mep-id 12 enable
    [SwitchA-md-test-ma-test] quit
    [SwitchA-md-test] quit
    

    # 配置SwitchB。

    <Quidway> system-view
    [Quidway] sysname SwitchB
    [SwitchB] vlan batch 11
    [SwitchB] interface gigabitethernet 1/0/1
    [SwitchB-GigabitEthernet1/0/1] port hybrid pvid vlan 11
    [SwitchB-GigabitEthernet1/0/1] port hybrid untagged vlan 11
    [SwitchB-GigabitEthernet1/0/1] quit
    [SwitchB] cfm enable
    [SwitchB] cfm md test
    [SwitchB-md-test] ma test
    [SwitchB-md-test-ma-test] map vlan 11
    [SwitchB-md-test-ma-test] mep mep-id 12 interface gigabitethernet1/0/1 outward
    [SwitchB-md-test-ma-test] mep ccm-send mep-id 12 enable
    [SwitchB-md-test-ma-test] remote-mep mep-id 11
    [SwitchB-md-test-ma-test] remote-mep ccm-receive mep-id 11 enable
    [SwitchB-md-test-ma-test] quit
    [SwitchB-md-test] quit

  2. 配置SwitchA,使能NQA客户端,配置普通隧道的MAC Ping测试例。

    [SwitchA]nqa test-instance admin macping
    [SwitchA-nqa-admin-macping] test-type macping
    [SwitchA-nqa-admin-macping] md test ma test
    [SwitchA-nqa-admin-macping] destination-address remote-mep mep-id 12

  3. 启动测试操作

    [SwitchA-nqa-admin-macping] start now

  4. 验证测试结果

    [SwitchA-nqa-admin-macping] display nqa results test-instance admin macping
    
     NQA entry(admin, macping) :testflag is inactive ,testtype is macping
      1 . Test 1 result   The test is finished
       SendProbe:3                          ResponseProbe:3
       Completion:success                   RTD OverThresholds number:0
       OWD OverThresholds SD number:0       OWD OverThresholds DS number:0
       Min/Max/Avg/Sum RTT:3/3/3/9          RTT Square Sum:27
       NumOfRTT:3                           Drop operation number:0
       Operation sequence errors number:0   RTT Stats errors number:0
       System busy operation number:0       Operation timeout number:0
       Min Positive SD:0                    Min Positive DS:0
       Max Positive SD:0                    Max Positive DS:0
       Positive SD Number:0                 Positive DS Number:0
       Positive SD Sum:0                    Positive DS Sum:0
       Positive SD Square Sum:0             Positive DS Square Sum:0
       Min Negative SD:0                    Min Negative DS:0
       Max Negative SD:0                    Max Negative DS:0
       Negative SD Number:0                 Negative DS Number:0
       Negative SD Sum:0                    Negative DS Sum:0
       Negative SD Square Sum:0             Negative DS Square Sum:0
       Min Delay SD:0                       Min Delay DS:0
       Avg Delay SD:0                       Avg Delay DS:0
       Max Delay SD:0                       Max Delay DS:0
       Delay SD Square Sum:0                Delay DS Square Sum:0
       Packet Loss SD:0                     Packet Loss DS:0
       Packet Loss Unknown:0                Average of Jitter:0
       Average of Jitter SD:0               Average of Jitter DS:0
       Jitter out value:0.0000000           Jitter in value:0.0000000
       NumberOfOWD:0                        Packet Loss Ratio: 0%
       OWD SD Sum:0                         OWD DS Sum:0
       ICPIF value: 0                       MOS-CQ value: 0
       TimeStamp unit: ms                   Packet Rewrite Number: 0
       Packet Rewrite Ratio: 0%             Packet Disorder Number: 0
       Packet Disorder Ratio: 0%            Fragment-disorder Number: 0
       Fragment-disorder Ratio: 0%          Jitter OverThresholds SD number:0
       Jitter OverThresholds DS number:0    OverallOverThresholds number:0
       Start time: --
       End time: --
    

配置文件

  • SwitchA的配置文件

    #
    sysname SwitchA
    #
    vlan batch 11
    #
    cfm enable
    #
    interface GigabitEthernet1/0/1
     port hybrid pvid vlan 11
     port hybrid untagged vlan 11
    #
    cfm md test
     ma test
      map vlan 11
      mep mep-id 11 interface GigabitEthernet1/0/1 outward
      mep ccm-send mep-id 11 enable
      remote-mep mep-id 12
      remote-mep ccm-receive mep-id 12 enable
    #
    nqa test-instance admin macping
     test-type macping
     destination-address remote-mep mep-id 12
     md test ma test
    #
    return
  • SwitchB的配置文件

    #
    sysname SwitchB
    #
    vlan batch 11
    #
    cfm enable
    #
    interface GigabitEthernet1/0/1
     port hybrid pvid vlan 11
     port hybrid untagged vlan 11
    #
    cfm md test
     ma test
      map vlan 11
      mep mep-id 12 interface GigabitEthernet1/0/1 outward
      mep ccm-send mep-id 12 enable
      remote-mep mep-id 11
      remote-mep ccm-receive mep-id 11 enable
    #
    return
翻译
下载文档
更新时间:2019-08-21

文档编号:EDOC1000141529

浏览量:20354

下载量:402

平均得分:
本文档适用于这些产品
相关文档
相关版本
Share
上一页 下一页