评分并提供意见反馈 :
华为采用机器翻译与人工审校相结合的方式将此文档翻译成不同语言，希望能帮助您更容易理解此文档的内容。 请注意：即使是最好的机器翻译，其准确度也不及专业翻译人员的水平。 华为对于翻译的准确性不承担任何责任，并建议您参考英文文档（已提供链接）。
配置Trace测试示例
操作步骤
- 按图7-26配置各接口的IP地址并配置Router之间路由可达
<Huawei> system-view[Huawei] sysname RouterA
[RouterA] interface gigabitethernet 1/0/0
[RouterA-GigabitEthernet1/0/0] ip address 10.1.1.1 24
[RouterA-GigabitEthernet1/0/0] quit
[RouterA] ip route-static 10.2.1.0 255.255.255.0 10.1.1.2RouterB和RouterC的配置请参考配置文件。
- 在RouterA上配置Trace类型的NQA测试例，目的地址为10.2.1.2
[RouterA] nqa test-instance admin trace[RouterA-nqa-admin-trace] test-type trace[RouterA-nqa-admin-trace] destination-address ipv4 10.2.1.2 - 启动测试
[RouterA-nqa-admin-trace] start now - 验证配置结果
# 在RouterA上查看NQA测试结果。
[RouterA-nqa-admin-trace] display nqa results test-instance admin traceNQA entry(admin, trace) :testflag is inactive ,testtype is trace 1 . Test 1 result The test is finished Completion:success Attempts number:1 Disconnect operation number:0 Operation timeout number:0 System busy operation number:0 Connection fail number:0 Operation sequence errors number:0 RTT Stats errors number:0 Drop operation number:0 Last good path Time:2012-07-17 11:21:27.2 1 . Hop 1 Send operation times: 3 Receive response times: 3 Min/Max/Average Completion Time: 1/1/1 Sum/Square-Sum Completion Time: 3/3 RTD OverThresholds number: 0 Last Good Probe Time: 2012-07-17 11:21:27.2 Destination ip address:10.1.1.2 Lost packet ratio: 0 % 2 . Hop 2 Send operation times: 3 Receive response times: 3 Min/Max/Average Completion Time: 1/1/1 Sum/Square-Sum Completion Time: 3/3 RTD OverThresholds number: 0 Last Good Probe Time: 2012-07-17 11:21:27.2 Destination ip address:10.2.1.2 Lost packet ratio: 0 %
配置文件
RouterA的配置文件
# sysname RouterA # interface GigabitEthernet1/0/0 ip address 10.1.1.1 255.255.255.0 # ip route-static 10.2.1.0 255.255.255.0 10.1.1.2 # nqa test-instance admin trace test-type trace destination-address ipv4 10.2.1.2 # return
RouterB的配置文件
# sysname RouterB # interface GigabitEthernet1/0/0 ip address 10.1.1.2 255.255.255.0 # interface GigabitEthernet2/0/0 ip address 10.2.1.1 255.255.255.0 # return
RouterC的配置文件
# sysname RouterC # icmp port-unreachable send # interface GigabitEthernet1/0/0 ip address 10.2.1.2 255.255.255.0 # ip route-static 10.1.1.0 255.255.255.0 10.2.1.1 # return
