评分并提供意见反馈 :
华为采用机器翻译与人工审校相结合的方式将此文档翻译成不同语言，希望能帮助您更容易理解此文档的内容。 请注意：即使是最好的机器翻译，其准确度也不及专业翻译人员的水平。 华为对于翻译的准确性不承担任何责任，并建议您参考英文文档（已提供链接）。
display mpls l2vpn diag-info reason-code
使用指南
PW状态变化原因具有两个标识，其中一个是原因代码，另一个是原因的描述信息。前者便于管理，后者便于理解。当需要根据原因代码查看具体的描述信息时，可以执行display mpls l2vpn diag-info reason-code命令查看PW状态变化的原因描述信息。
使用实例
# 查看PW状态变化的原因代码所对应的状态描述信息。
<HUAWEI> system-view
[~HUAWEI] diagnose
[~HUAWEI-diagnose] display mpls l2vpn diag-info reason-code
ID State Change Reason
1 Invalid reason type
2 VC was created
3 VC was deleted
4 LDP session was Down
5 LDP session was Up
6 Same LDP mapping was received with different label and MTU
7 Same LDP mapping was received with matching interface parameters
8 LDP mapping was received with mismatching interface parameters
9 LDP Mapping Received UnPass CBit Check
10 LDP mapping was received with unpass PW loop check
11 New LDP mapping message was received
12 New LDP mapping message was received but remote VC or local VC is Down
13 LDP withdraw message was received
14 LDP release message was received
15 LDP request message was received
16 LDP GR ended processing
17 RSVP message was received
18 Interface was Up
19 Interface was Down
20 Encapsulation changed
21 Refresh
22 Download Again
23 Tunnel was Up
24 Tunnel was Down
25 VC state changed when New RLB was received
26 RLB was Deleted
27 VC was created or connected to another remote CE
28 Outgoing interface was unavailable
29 Outgoing interface was available
30 LDP notification message was forwarded
31 LDP notification message was not forwarded
32 PW was recreated
33 Download FTN&ILM for EthernetTrunk
34 AC OAM fault detection was disabled
35 Remote AC fault
36 Remote AC fault was resumed
37 Local AC fault
38 Local AC fault was resumed
39 PSN fault
40 PSN Fault Resume
41 Local PSN Fault
42 Local PSN fault was resumed
43 BFD for pw status changed to Down
44 BFD for pw status changed to UP
45 BFD for pw status changed to Admin down
46 BFD for pw was disabled
47 Manual set was enabled
48 Manual set was disabled
49 Delay timed out
50 Resume timed Out
51 Vrrp status changed to Master
52 Vrrp status changed to Backup
53 Vrrp status changed to Init
54 Vrrp was deleted
55 Track vrrp
56 Undo track vrrp
57 Lsp Ping Time Out
58 VC state down when New RLB was received
59 MTU Matched
60 MTU Unmatched
61 VSI was shuted
62 VSI was resumed
63 Set Admin VSI
64 Undo set Admin VSI
65 B-VSI Bind Interface
66 B-VSI Unbind Interface
67 I-VSI Bind B-VSI
68 I-VSI Unbind B-VSI
69 Vsi was deleted
70 Reconstruct Forward Table
71 E-Trunk Become Master
72 E-Trunk Become Backup
73 Administrator PW Up
74 Administrator PW Down
75 VCCV OK
76 VCCV Failed
77 Local Ifnet Resource Available
78 In Label Resource Available
79 Local Ifnet Resource Release
80 In Label Resource Release
81 Switch Over Operation Enable
82 Switch Over Operation Disable
83 Set The VSI as B-component
84 Undo Set The VSI as B-component
85 B-component VSI Shutdown
86 Undo B-component VSI Shutdown
87 Notification Received
88 PW Aps Switch
89 Route UnReachable
90 Route Reachable
91 Other PWs were deleted
92 VAPW up
93 Soft reset resumed
94 Token resource exceed
95 Token resource exceed resumed
表16-30 display mpls l2vpn diag-info reason-code命令输出信息描述
项目 |
描述 |
|---|---|
ID |
PW状态变化的原因代码 |
State Change Reason |
PW状态变化的原因描述信息 |
上一页
