所选语种没有对应资源,请选择:

本站点使用Cookies,继续浏览表示您同意我们使用Cookies。Cookies和隐私政策>

提示

尊敬的用户,您的IE浏览器版本过低,为获取更好的浏览体验,请升级您的IE浏览器。

升级

CX916, CX916L, CX930 交换模块 V100R001 诊断命令参考 04

评分并提供意见反馈 :
华为采用机器翻译与人工审校相结合的方式将此文档翻译成不同语言,希望能帮助您更容易理解此文档的内容。 请注意:即使是最好的机器翻译,其准确度也不及专业翻译人员的水平。 华为对于翻译的准确性不承担任何责任,并建议您参考英文文档(已提供链接)。
pads diagnose neighbor bgp

pads diagnose neighbor bgp

命令功能

pads diagnose neighbor bgp命令用来查看BGP邻居建立失败或邻居断开连接的原因。

命令格式

pads diagnose neighbor { establish-abnormal | flap } bgp history-record

pads diagnose neighbor { establish-abnormal | flap } bgp peer ipv4-address

pads diagnose neighbor { establish-abnormal | flap } bgp vpnv4 vpn-instance vpn-instance-name peer ipv4-address

pads diagnose neighbor { establish-abnormal | flap } bgp vpnv4 vpn-instance vpn-instance-name history-record

参数说明

参数 参数说明 取值
establish-abnormal 显示BGP邻居建立失败的原因。 -
flap 显示BGP邻居断开连接的原因。 -
history-record 显示BGP邻居建立失败或邻居断开连接的原因的历史记录。 -
peer ipv4-address 指定BGP邻居的IP地址。 点分十进制形式。
vpnv4 指定VPNv4地址族。 -
vpn-instance vpn-instance-name 指定VPN实例的名称。 字符串形式,区分大小写,不支持空格,长度范围是1~31。不能以“_public_”作为VPN实例名称。当输入的字符串两端使用双引号时,可在字符串中输入空格。

视图

诊断视图

缺省级别

3:管理级

使用指南

通过pads diagnose neighbor bgp命令,可以快速查看BGP邻居建立失败或邻居断开连接的原因,方便定位问题。

使用实例

# 显示所有公网BGP邻居建立失败的原因的历史记录。

<HUAWEI> system-view
[~HUAWEI] diagnose
[~HUAWEI-diagnose] pads diagnose neighbor establish-abnormal bgp history-record
Start diagnose at 2018-04-17 08:07:51, Estimated time:80 seconds.
........
End diagnose at 2018-04-17 08:07:59, Actual time:8 seconds.
Diagnose report:
                                                             
IPv4-family for public instance :
BGP local router ID : 1.1.1.2 
------------------------------------------------------------------------------------------                                                            
NBR-Peer-IP     Last-Detect-Time State       Reason
1.1.1.1         01-27 20:23:49   OpenConfirm The shutdown command is run in the BGP view. 
2.2.2.2         01-27 20:23:49   Idle        The peer ignore command is configured for the BGP peer.

# 显示指定公网BGP邻居建立失败的原因。

<HUAWEI> system-view
[~HUAWEI] diagnose
[~HUAWEI-diagnose] pads diagnose neighbor establish-abnormal bgp peer 1.1.1.1
Start diagnose at 2018-04-17 08:07:51, Estimated time:80 seconds.
........
End diagnose at 2018-04-17 08:07:59, Actual time:8 seconds.
Diagnose report:
                                                             
IPv4-family for public instance :
BGP local router ID : 10.1.1.2 
------------------------------------------------------------------------------------------                                                            
NBR-Peer-IP     Last-Detect-Time State        Reason
1.1.1.1         01-27 20:23:49   OpenConfirm  BGP does not start the connection state machine, and the instance configuration is not synchronized to the BRM component. 

# 显示私网BGP邻居建立失败的原因的历史记录。

<HUAWEI> system-view
[~HUAWEI] diagnose
[~HUAWEI-diagnose] pads diagnose neighbor establish-abnormal bgp vpnv4 vpn-instance vpn1 history-record
Start diagnose at 2018-04-17 08:07:51, Estimated time:80 seconds.
........
End diagnose at 2018-04-17 08:07:59, Actual time:8 seconds.
Diagnose report:
                          
IPv4-family for vpn instance :
VPN-Instance vpn1, Router ID 10.1.1.2: 
------------------------------------------------------------------------------------------
NBR-Peer-IP     Last-Detect-Time State        Reason
1.1.1.1         01-27 20:23:49   OpenConfirm  Missing peer connect-interface configuration 
2.2.2.2         01-27 20:23:49   Idle         An Open message with an incorrect peer router ID is received. The router ID (0.0.0.0) of the peer is invalid or conflicts with the router ID (189.77.144.250) of the local device.

# 显示所有公网BGP邻居断开连接的原因的历史记录。

<HUAWEI> system-view
[~HUAWEI] diagnose
[~HUAWEI-diagnose] pads diagnose neighbor flap bgp history-record
Start diagnose at 2018-04-17 08:07:51, Estimated time:80 seconds.
........
End diagnose at 2018-04-17 08:07:59, Actual time:8 seconds.
Diagnose report:
                          
IPv4-family for public instance :
BGP local router ID : 10.1.1.2 
------------------------------------------------------------------------------------------
NBR-Peer-IP     NBR-Down-Time    State              Reason
1.1.1.1         01-27 20:23:49   Established->Idle  Received Open message in ESTABLISHED state.
2.2.2.2         01-27 20:23:49   Established->Idle  This device cfg change: peer ignore.
表12-191 pads diagnose neighbor bgp命令输出信息描述

项目

描述

Start diagnose

开始诊断时间。

Estimated time

预计使用的时间。

End diagnose

结束诊断时间。

Actual time

实际使用的时间。

IPv4-family for public instance

公网BGP-IPv4地址族。

BGP local router ID

本地BGP设备的ID号,其格式与IPv4地址一样。

NBR-Peer-IP

BGP邻居IP地址。

Last-Detect-Time

上一次检测的时间。

State

当查看BGP邻居建立失败的原因时,表示邻居的状态。

当查看BGP邻居断开连接的原因时,表示邻居的状态变化。

Reason

BGP邻居建立失败或者断开连接的原因。

详细原因请参见表12-192表12-193

IPv4-family for vpn instance

私网IPv4地址族。

VPN-Instance vpn1, Router ID 10.1.1.2

VPN实例名称和Router ID。

NBR-Down-Time

BGP邻居断开连接的时间。

表12-192 BGP邻居建立失败原因列表

项目

描述

The local address is x.x.x.x, and the peer address is x.x.x.x. The peer connect-interface command configuration on the local end is incorrect, or the peer address is incorrect.

配置错误,本机地址是x.x.x.x,邻居地址是x.x.x.x,本端connect-interface配置错误或者对端Peer地址错误。

The IP address of a loopback interface is used to establish a BGP peer relationship, but the peer connect-interface command is not configured.

配置错误,使用Loopback地址建立BGP邻居,但是没有配置peer connect-interface命令。

BGP does not start the connection state machine, and the SOCK component fails to be registered.

BGP未启动建连状态机,Socket组件注册失败。

BGP does not start the connection state machine, and the instance or peer is deleted.

BGP未启动建连状态机,Instance或者Peer处于删除状态。

BGP does not start the connection state machine, and the source IP address of the BGP peer is invalid.

BGP未启动建连状态机,BGP邻居源地址无效。

The BGP router ID is 0.

BGP的Router-id为0。

BGP does not start the connection state machine, and the instance configuration is not synchronized to the BRM component.

BGP未启动建连状态机,Instance配置未同步到BRM。

BGP does not start the connection state machine, and the peer configuration is not synchronized to the BRM component.

BGP未启动建连状态机,Peer配置未同步到BRM。

The peer ignore command is configured for the BGP peer.

BGP邻居配置了peer ignore命令。

The shutdown command is run in the BGP view.

BGP配置了shutdown命令。

The corresponding address family is not enabled for the BGP peer.

BGP邻居没有使能对应的地址族。

BGP does not start the connection state machine, and the BNM component is waiting for a peer Down acknowledgement from the BRM xxxx component.

BGP未启动建连状态机,BNM等待BRM回应peer down ack消息。

BGP does not start the connection state machine, and the BGP peer is in the reset state.

BGP未启动建连状态机,BGP邻居处于reset状态。

The peer route-limit command is run, and the number of routes received from the BGP peer exceeds the configured limit.

BGP邻居配置了peer route-limit命令,且该邻居接收的路由已经超限。

The peer route-limit idle-forever command is run, and the peer is in the Idle forever state.

BGP邻居配置了peer route-limit idle-forever命令,Peer处于Idle forever状态。

The peer ebgp-max-hop or peer valid-ttl-hops command is not configured for the BGP peer.

BGP邻居上缺少ebgp-max-hop或者valid-ttl-hops配置。

BGP does not start the connection state machine, and nor is the peer Down backup over.

BGP未启动建连状态机,Peer Down备份未完成。

The BGP peer uses a link-local address, but the peer connect-interface command is not configured.

BGP邻居是Link-local地址,但未配置connect-interface命令。

BGP does not start the connection state machine. When the device attempts to establish a BGP peer relationship, it finds that a BFD session already exists.

BGP未启动建连状态机,BGP邻居建立时,发现已经存在BFD会话。

BGP does not start the connection state machine, and nor is the BRM xxxx component ready.

BGP未启动建连状态机,BRM_xxxx组件未ready。

An Open message with an incorrect version is received. The version of the received message is xxx, and the expected version is 4.

收到错误的Open报文,版本号错误,收到的版本号是xxx,期望的版本号是4。

The HoldTime negotiation through Open messages fails. The HoldTime value of the peer is xxxx, and the MinHoldTime value of the local device is xxx. The expected HoldTime value of the peer is 0 or an integer larger than 2s and the local MinHoldTime value.

收到的Open报文中HoldTime协商失败,对端邻居的HoldTime值是xxxx,本地设备的MinHoldTime值是xxx。期望值:对端邻居的HoldTime值大于2s和本地MiniHoldTime值,或者对端邻居的HoldTime值为0。

An Open message with an incorrect peer router ID is received. The router ID (xxxx) of the peer is invalid or conflicts with the router ID (xxxx) of the local device.

收到错误的Open报文,邻居的Router-id非法,或者与本地设备的Router-id冲突,邻居Router-id为xxxx,本地Router-id为xxxx。

An Open message with optional parameter data whose length is invalid is received. The length of the received data is xxx, and the expected data length is xxxx.

收到错误的Open报文,可选参数长度非法,接收到的数据长度为xxx,期望的数据长度为xxxx。

When the optional parameter in the Open message is processed, the MBUF function fails to be invoked.

处理Open报文可选参数时,MBUF函数返回失败。

An Open message with optional capability data whose length is invalid is received. The length of the received data is xxxx, and the expected data length is xxxx.

收到错误的Open报文,可选能力长度非法,接收到的数据长度为xxxx,期望的数据长度为xxxx。

When the optional capability in the Open message is processed, the MBUF function fails to be invoked.

处理Open报文可选能力时,MBUF函数返回失败。

An Open message with MP data whose length is invalid is received. The length of the received data is xxxx, and the expected data length is xxxx.

收到错误的Open报文,多协议扩展数据长度非法,接收到的数据长度为xxxx,期望的数据长度为xxxx。

When the MP data in the Open message is processed, the MBUF function fails to be invoked.

处理Open报文多协议扩展数据时,MBUF函数返回失败。

An Open message with refresh capability data whose length is invalid is received. The length of the received data is xxxx, and the expected data length is xxxx.

收到错误的Open报文,refresh能力数据长度非法,接收到的数据长度为xxxx,期望的数据长度为xxxx。

An Open message with GR capability data whose length is invalid is received. The length of the received data is xxxx, and the expected data length is xxxx.

收到错误的Open报文,GR能力数据长度非法,接收到的数据长度为xxxx,期望的数据长度为xxxx。

When the GR capability in the Open message is processed, the MBUF function fails to be invoked.

处理Open报文GR能力数据时,MBUF函数返回失败。

An Open message with 4-byte AS number data whose length is invalid is received. The length of the received data is xxxx, and the expected data length is xxxx.

收到错误的Open报文,4字节AS号数据长度非法,接收到的数据长度为xxxx,期望的数据长度为xxxx。

When the 4-byte AS number in the Open message is processed, the MBUF function fails to be invoked.

处理Open报文4字节AS号数据时,MBUF函数返回失败。

When the ORF capability in the Open message is processed, the MBUF function fails to be invoked.

处理Open报文ORF能力数据时,MBUF函数返回失败。

An Open message with Add-Path capability data whose length is invalid is received. The length of the received data is xxxx, and the expected data length is xxxx.

收到错误的Open报文,Add-Path能力数据长度非法,接收到的数据长度为xxxx,期望的数据长度为xxxx。

When the Add-Path capability in the Open message is processed, the MBUF function fails to be invoked.

处理Open报文Add-Path能力数据时,MBUF函数返回失败。

An Open message with RR+ capability data whose length is invalid is received. The length of the received data is xxxx, and the expected data length is xxxx.

收到错误的Open报文,RR+能力数据长度非法,接收到的数据长度为xxxx,期望的数据长度为xxxx。

When the RR+ capability in the Open message is processed, the MBUF function fails to be invoked.

处理Open报文RR+能力数据时,MBUF函数返回失败。

The AS number negotiation through Open messages fails. The local AS number is xxx, and the peer AS number is xxxx.

收到的Open报文中AS号协商失败,本地peer配置的AS号为xxx,对端设备的AS号为xxxx。

The BGP address families configured for the local and peer devices do not match.

本端设备和对端设备没有配置匹配的BGP地址族。

The Add-Path capabilities configured for the BGP labeled address family and the BGP unicast address family are inconsistent in the received Open message. The Add-Path capability must be configured for both the BGP labeled address family and the BGP unicast address family, and the receive or send parameter configurations must be the same.

收到的Open报文中标签和单播地址族Add-Path能力不一致,Add-Path能力必须同时包括标签和单播地址族,且Receive/Send相同 。

Tcp connect failed because md5 mismatch.

本端设备和对端设备的Peer Password配置不一致。

Tcp connect failed because no route.

没有对端Peer的路由。

Attach socket failed on slave.

备板Attach Socket失败。

The neighbor device close socket normally.

对端设备正常关闭了Socket,本端设备Socket收到了对端设备TCP的RST报文。

The neighbor device close socket forcely.

对端设备强制关闭了Socket,本端设备Socket收到了对端设备TCP的FIN报文。

Tcp connect failed because no syn packet received.

没有收到握手报文导致TCP连接建立失败。

Tcp connect failed because keychain mismatch.

本端设备和对端设备的Peer Keychain配置不一致。

Tcp connect failed because only config local or neighbor's keychain.

本端和对端设备,只有一端配Keychain导致TCP连接建立失败。

Tcp connect failed because socket creat path failed, errcode code is xxxx (socket check route failed).

不存在路由,TCP查询超时导致TCP连接建立失败,错误码为xxx。

Tcp connect failed because socket creat path failed, errcode code is xxxx (socket check arp failed) .

存在路由,TCP查询ARP超时导致TCP连接建立失败,错误码为xxx。

Tcp connect failed because peer addr no arp.

存在路由,没有ARP导致TCP连接建立失败。

In the direction of receiving, LDM send packet error, Hcid is xxx, ErrCode is xxx, SubErrCode is xxx.

BGP建连失败,LDM收方向接收数据失败,错误码为xxxx,子错误码为xxxx。

In the direction of receiving, Socket send packet error, Hcid is xxx, ErrCode is xxx, SubErrCode is xxx.

BGP建连失败,Socket收方向接收数据失败,错误码为xxxx,子错误码为xxxx。

In the direction of sending, LDM revived packet error, Hcid is xxx, ErrCode is xxx, SubErrCode is xxx.

BGP建连失败,LDM发方向发送数据失败,错误码为xxxx,子错误码为xxxx。

In the direction of sending, Socket revived packet error, Hcid is xxx, ErrCode is xxx, SubErrCode is xxx.

BGP建连失败,Socket发方向接收数据失败,错误码为xxxx,子错误码为xxxx。

In the direction of receiving, Device processing packet timeout, LDM received at xxx, Socket received at xxx, Bgp received at xxx.

BGP建连失败,收方向接收数据超时,LDM接收时间为xxx,Socket接收时间为xxxx,BGP接收时间为xxxx。

In the direction of sending, Device processing packet timeout, Socket send at xxx, LDM send at xxx.

BGP建连失败,发方向发送数据超时,Socket接收时间为xxxx,LDM接收时间为xxxx。

In the direction of receiving, Device processing packet timeout, LDM in at xxx,LDM out at xxx, Socket don't send to bgp.

BGP建连失败,检测Socket收方向接收数据超时,LDM接收时间为xxx,LDM发送时间为xxxx。

Open message sent failed because mbuf alloc failed.

申请mbuf失败导致向对端邻居发送Open报文失败。

Open message sent failed because flow control.

消息被流控导致向对端邻居发送Open报文失败。

Open message sent failed because token alloc failed.

申请令牌失败导致向对端邻居发送Open报文失败。

Open message sent failed because socket return error xxx.

Socket返回错误(错误码为xxx)导致向对端邻居发送Open报文失败。

Keepalive message sent failed because socket return error xxx.

Socket返回错误(错误码为xxx)导致向对端邻居发送Keeplive报文失败。

Idle hold timer exist, delay connect time value is xxx s.

延迟建连定时器未超时,没有触发建连。

No open or keepalive message are received, and the internal communication of the device is normal.

没有收到Open或者Keeplive报文,链路正常。

The socket state machine is incorrect, or the pipe is not enabled.

Socket状态机错误,或者管道没有打开。

表12-193 BGP邻居震荡原因列表

项目

描述

This device cfg change: undo peer.

配置undo peer命令导致BGP断连。

This device cfg change: peer ignore.

配置peer ignore命令导致BGP断连。

This device cfg change: reset bgp.

配置reset peer命令导致BGP断连。

This device cfg change: peer connect-interface.

配置peer connect-interface命令导致BGP断连。

This device cfg change: peer connect-only.

配置peer connect-only命令导致BGP断连。

This device cfg change: peer listen-only.

配置peer listen-only命令导致BGP断连。

This device cfg change: peer capability-advertise 4-byte-as.

配置peer capability-advertise 4-byte-as命令导致BGP断连。

This device cfg change: peer capability-advertise route-refresh.

配置peer capability-advertise route-refresh命令导致BGP断连。

This device cfg change: peer capability-advertise conventional.

配置peer capability-advertise conventional命令导致BGP断连。

This device cfg change: peer capability-advertise add-path.

配置peer capability-advertise add-path命令导致BGP断连。

This device cfg change: peer valid-ttl-hops.

配置peer valid-ttl-hops命令导致BGP断连。

This device cfg change: peer ebgp-max-hop.

配置peer ebgp-max-hop命令导致BGP断连。

This device cfg change: peer timer.

配置peer timer命令导致BGP断连。

This device cfg change: graceful-restart.

配置graceful-restart命令导致BGP断连。

This device cfg change: peer label-route-capability.

配置peer label-route-capability命令导致BGP断连。

This device cfg change: peer capability-advertise orf.

配置peer capability-advertise orf命令导致BGP断连。

This device cfg change: peer as-number.

配置peer as-number命令导致BGP断连。

This device cfg change: peer capability-advertise route-policy-distribute.

配置peer capability-advertise route-policy-distribute命令导致BGP断连。

This device cfg change: peer tcp-mss.

配置peer tcp-mss命令导致BGP断连。

This device cfg change: graceful-restart timer.

配置graceful-restart timer命令导致BGP断连。

This device cfg change: local as change.

配置local as change命令导致BGP断连。

This device cfg change: confederation id.

配置confederation id命令导致BGP断连。

This device cfg change: confederation peer-as.

配置confederation peer-as命令导致BGP断连。

This device cfg change: reset bgp.

配置reset bgp命令导致BGP断连。

This device cfg change: shutdown (BGP).

配置shutdown(BGP)命令导致BGP断连。

This device cfg change : router-id (BGP).

配置router-id命令导致BGP断连。

This device cfg change : peer x.x.x.x enable.

配置peer enable命令导致BGP断连,触发断连。

This device cfg change : undo peer x.x.x.x enable.

配置undo peer enable命令导致BGP断连,触发断连。

Received Notification from neighbor, Header Error/Connection Not Synchronized.

收到Notification报文,BGP报文头错误,未同步。

Received Notification from neighbor, Message Header Error/Bad Message Length.

收到Notification报文,消息头错误,长度错误。

Received Notification from neighbor, Message Header Error/Bad Message Type.

收到Notification报文,消息头错误,类型错误。

Received Notification from neighbor, OPEN Message Error/Unsupported Version Number.

收到Notification报文,Open报文错误,版本号错误。

Received Notification from neighbor, OPEN Message Error/Bad Peer AS.

收到Notification报文,Open报文错误,对端AS错误。

Received Notification from neighbor, OPEN Message Error/Bad BGP Identifier.

收到Notification报文,Open报文错误,对端Router-ID错误。

Received Notification from neighbor, OPEN Message Error/Unsupported Optional Parameter.

收到Notification报文,Open报文错误,可选参数列表错误。

Received Notification from neighbor, OPEN Message Error/Authentication Failure.

收到Notification报文,Open报文错误,认证失败。

Received Notification from neighbor, OPEN Message Error/Unacceptable Hold Time.

收到Notification报文,Open报文错误,HoldTimer时间错误。

Received Notification from neighbor, OPEN Message Error/Unsupported Capability.

收到Notification报文,Open报文错误,不支持的能力。

Received Notification from neighbor, UPDATE Message Error/Malformed Attribute List.

收到Notification报文,Open报文错误,属性错误。

Received Notification from neighbor, UPDATE Message Error/Unrecognized Well-known Attribute.

收到Notification报文,Open报文错误,公认属性不识别。

Received Notification from neighbor, UPDATE Message Error/Missing Well-known Attribute.

收到Notification报文,Open报文错误,缺少公认属性。

Received Notification from neighbor, UPDATE Message Error/Attribute Flags Error.

收到Notification报文,Open报文错误,属性标记错误。

Received Notification from neighbor, UPDATE Message Error/Attribute Length Error.

收到Notification报文,Open报文错误,属性长度错误。

Received Notification from neighbor, UPDATE Message Error/Invalid ORIGIN Attribute.

收到Notification报文,Open报文错误,无效Origin属性。

Received Notification from neighbor, UPDATE Message Error/AS Routing Loop

收到Notification报文,Open报文错误,AS号环路。

Received Notification from neighbor, UPDATE Message Error/Invalid NEXT_HOP Attribute.

收到Notification报文,Open报文错误,下一跳属性无效。

Received Notification from neighbor, UPDATE Message Error/Optional Attribute Error.

收到Notification报文,Open报文错误,可选属性无效。

Received Notification from neighbor, UPDATE Message Error/Invalid Network Field.

收到Notification报文,Open报文错误,Nework域无效。

Received Notification from neighbor, UPDATE Message Error/Malformed AS_PATH.

收到Notification报文,Open报文错误,AS号列表有误。

Received Notification from neighbor, Neighbor's Hold Timer Expired.

收到Notification报文,邻居的HoldTime超时。

Received Notification from neighbor, Finite State Machine Error.

收到Notification报文,对端邻居的状态机错误。

Received Notification from neighbor, CEASE/Maximum Number of Prefixes Reached.

收到Notification报文,对端邻居路由超限。

Received Notification from neighbor, CEASE/Administrative Shutdown.

收到Notification报文,对端邻居主动断连。

Received Notification from neighbor, CEASE/Peer De-configured.

收到Notification报文,对端邻居重复配置。

Received Notification from neighbor, CEASE/Administrative Reset.

收到Notification报文,对端邻居复位连接。

Received Notification from neighbor, CEASE/Connection Rejected.

收到Notification报文,对端邻居拒绝BGP连接。

Received Notification from neighbor, CEASE/Other Configuration Change.

收到Notification报文,对端邻居有配置变化。

Received Notification from neighbor, CEASE/Connection Collision Resolution.

收到Notification报文,连接有冲突。

Received Notification from neighbor, CEASE/Out of Resources.

收到Notification报文,对端设备资源不足。

Received Notification from neighbor, CEASE/BFD Session Down.

收到Notification报文,对端设备检测到BFD状态Down。

Received Notification from neighbor, Unknown ErrCode and ErrSubcode.

收到Notification报文,未知的错误码和子错误码。

Received error update msg, Attribute repeat : path attribute ORIGIN.

收到错误的Update报文,Origin属性重复。

Received error update msg, Attribute repeat : path attribute ASPATH.

收到错误的Update报文,ASPATH属性重复。

Received error update msg, Attribute repeat : path attribute NEXT HOP.

收到错误的Update报文,Nexthop属性重复。

Received error update msg, Attribute repeat : path attribute MED.

收到错误的Update报文,MED属性重复。

Received error update msg, Attribute repeat : path attribute LOCAL PREFERENCE.

收到错误的Update报文,Local Preference属性重复。

Received error update msg, Attribute repeat : path attribute ATOMIC-AGGREGATE.

收到错误的Update报文,Atomic-Aggregate属性重复。

Received error update msg, Attribute repeat : path attribute AGGREGATOR.

收到错误的Update报文,Aggregate属性重复。

Received error update msg, Attribute repeat : path attribute COMMUNITIES.

收到错误的Update报文,团体属性重复。

Received error update msg, Attribute repeat : path attribute ORIGINATORID.

收到错误的Update报文,Originatorid属性重复。

Received error update msg, Attribute repeat : path attribute CLUSTER LIST.

收到错误的Update报文,Cluster List属性重复。

Received error update msg, Attribute repeat : path attribute COMMUNITY DUMMY.

收到错误的Update报文,Community Dummy属性重复。

Received error update msg, Attribute repeat : path attribute MP_REACH_NLRI.

收到错误的Update报文,MP_Reach_NLRI属性重复。

Received error update msg, Attribute repeat : path attribute MP_UNREACH_NLRI.

收到错误的Update报文,MP_UnReach_NLRI属性重复。

Received error update msg, Attribute repeat : path attribute EXTENDED COMMUNITIES.

收到错误的Update报文,扩展团体属性重复。

Received error update msg, Attribute repeat : path attribute AS4_PATH.

收到错误的Update报文,4字节AS号重复。

Received error update msg, Attribute repeat : path attribute AS4_AGGREGATOR.

收到错误的Update报文,AS4_Aggregator属性重复。

Received error update msg, Attribute repeat : path attribute EVPN PMSITUNNEL.

收到错误的Update报文,EVPN Pmsitunnel属性重复。

Received error update msg, Attribute repeat : path attribute AIGP.

收到错误的Update报文,AIGP属性重复。

Received error update msg, Attribute repeat : path attribute BGP-LS.

收到错误的Update报文,BGP_LS属性重复。

Received error update msg, Attribute repeat : path attribute VXLAN_REMOTENEXTHOP.

收到错误的Update报文,Vxlan_RemoteNexthop属性重复。

Received error update msg, Attribute repeat : path attribute L2VPN_AD.

收到错误的Update报文,L2VPN_AD属性重复。

Received error update msg, Attribute repeat : unknown attribute.

收到错误的Update报文,未知的属性重复。

Received error update msg, Community attribute length error, current length is xxx, the right value is an integer multiple of xxx.

收到错误的Update报文,团体属性长度错误,收到数据的长度为xxxx,期望的数据长度为xxxx。

Received error update msg, Extcommunity attribute length error, current length is xxx, the right value is an integer multiple of xxx.

收到错误的Update报文,扩展团体属性长度错误,收到数据的长度为xxxx,期望的数据长度为xxxx。

Received error update msg, Private attribute error: AttrType = xxx.

收到错误的Update报文,私有属性错误,收到的私有属性值为xxx。

Received error update msg, Remote nexthop attribute length error, current length is xxx, the right value is xxx.

收到错误的Update报文,路由下一跳属性长度错误,收到数据的长度为xxxx,期望的数据长度为xxxx。

Received error update msg, Unrecognized well known attribute, AttrType = xxx.

收到错误的Update报文,不识别的公共属性,收到的公共属性值为xxx。

Received error update msg, Attribute flags error, AttrType = xxx, AttrFlag = xxx.

收到错误的Update报文,属性标记错误,收到的属性类型为xxxx,属性标记为xxx。

Received error update msg, Attribute length error, AttrType = xxx, AttrLen = xxx.

收到错误的Update报文,属性长度错误,收到的属性类型为xxx,属性长度为xxx。

Received error update msg, Invalid ORIGIN given is bad, Origin = xxx.

收到错误的Update报文,Origin属性错误,收到的Origin属性值为xxx。

Received error update msg, Invalid NEXT HOP Attribute.

收到错误的Update报文,Nexthop属性错误。

Received error update msg, Optional attribute error: cluster-list length is zero.

收到错误的Update报文,可选属性错误,cluster-list长度为0。

Received error update msg, Optional attribute error: MP NextHop length is error, current length is xxx, the right value is xxx.

收到错误的Update报文,可选属性错误,MP Nexthop长度错误,收到数据的长度为xxxx,期望的数据长度为xxxx。

Received error update msg, Optional attribute error: MP Reach Prefix length is error, current length is xxx, the right value is xxx.

收到错误的Update报文,可选属性错误,MP可达路由前缀长度为0,收到数据的长度为xxxx,期望的数据长度为xxxx。

Received error update msg, Invalid network, Prefix length is error, current length is xxx, the right value is xxx.

收到错误的Update报文,无效的路由,路由前缀长度错误,收到数据的长度为xxxx,期望的数据长度为xxxx。

Received error update msg, EBGP route AS is empty.

收到错误的Update报文,EBGP路由的AS号为空。

Received error update msg, EBGP first AS is not peer's AS, FirstAs = xxx, RemoteAs = xxx.

收到错误的Update报文,EBGP路由的第1个AS号不是邻居的AS号,收到报文的第1个AS号为xxx,对端邻居的AS号为xxxx。

Received error update msg, AS path length is error.

收到错误的Update报文,AS号长度错误。

Received error update msg, UNLRI total len error.

收到错误的Update报文,UNLRI 总长度错误。

Received error update msg, Path Attributes len error.

收到错误的Update报文,Path Attributes长度错误。

Received Open message in ESTABLISHED state.

在建连状态收到Open报文导致断连。

Received error RouteRefresh msg in ESTABLISHED state, error code is xxx.

在建连状态收到错误的Route Refresh报文导致断连,错误码为xxxx。

Received error message head in ESTABLISHED state.

在建连状态收到错误的报文头导致断连。

Received error update message in ESTABLISHED state.

在建连状态收到错误的Update报文导致断连。

This device Hold Timer Expired. In the direction of receiving, LDM revived packet error, Hcid is xxx, ErrCode is xxx, SubErrCode is xxx.

HoldTime超时触发BGP断连,LDM在收方向接收数据失败,错误码为xxx,子错误码为xxx。

This device Hold Timer Expired. In the direction of receiving, SOCKET revived packet error, Hcid is xxx, ErrCode is xxx, SubErrCode is xxx .

HoldTime超时触发BGP断连,SOCKET在收方向接收数据失败,错误码为xxx,子错误码为xxx。

This device Hold Timer Expired. In the direction of receiving, Device processing packet timeout, LDM received at xxx, Socket received at xxx, Bgp received at xxx.

HoldTime超时触发BGP断连,收方向接收数据超时,LDM接收时间为xxx,Socket接收时间为xxx,BGP接收时间为xxx。

This device Hold Timer Expired. In the direction of receiving, Device processing packet timeout, LDM in at xxx,LDM out at xxx, Socket don't send to bgp.

HoldTime超时触发BGP断连,SOCKET在收方向接收数据超时处理,LDM接收时间为xxx,LDM发送时间为xxx。

This device Hold Timer Expired, the internal communication of the device is normal.

HoldTime超时,链路正常。

This device Hold Timer Expired.

本机的HoldTime超时。

This device reached maximum number of prefixes, please check the route limit.

本机路由数目超限触发断连。

The internal communication of the device is abnormal and the packet is not sent.

发方向自动发起检测,LDM检测发送失败。

Directly connected interface down.

直连接口Down触发BGP断连。

Need send refresh message to peer, but peer don't support refresh capability.

需要给BGP邻居发送Refresh报文,但是对端邻居不支持Route Refresh能力,导致BGP断连。

This device Hold Timer Expired, Tcp packet-dropping because md5 mismatch.

MD5错误,TCP丢包,导致BGP超时断连。

This device Hold Timer Expired, Tcp packet-dropping because keychain mismatch.

本端和对端设备都配置keychain,但不一致,TCP丢包,导致BGP超时断连。

This device Hold Timer Expired, Tcp packet-dropping because only config local or neighbor's keychain.

本端和对端设备,只有一端配置Keychain,TCP丢包,导致BGP超时断连。

Peer tracking detection triggers the BGP disconnection.

Peer tracking检测触发BGP断连。

翻译
下载文档
更新时间:2019-08-09

文档编号:EDOC1000178140

浏览量:5062

下载量:56

平均得分:
本文档适用于这些产品
相关版本
相关文档
Share
上一页 下一页