评分并提供意见反馈 :
华为采用机器翻译与人工审校相结合的方式将此文档翻译成不同语言，希望能帮助您更容易理解此文档的内容。 请注意：即使是最好的机器翻译，其准确度也不及专业翻译人员的水平。 华为对于翻译的准确性不承担任何责任，并建议您参考英文文档（已提供链接）。
配置NQA检测MPLS网络连通性示例
本示例通过LSP ping测试检测MPLS网络连通性。
操作步骤
- 配置LSP Ping测试用例
<DeviceA> system-view [~DeviceA] nqa test-instance admin lspping [*DeviceA-nqa-admin-lspping] test-type lspping [*DeviceA-nqa-admin-lspping] lsp-type ipv4 [*DeviceA-nqa-admin-lspping] destination-address ipv4 3.3.3.9 lsp-masklen 32
- 启动测试操作
[*DeviceA-nqa-admin-lspping] start now [*DeviceA-nqa-admin-lspping] commit
- 验证测试结果。
[~DeviceA-nqa-admin-lspping] display nqa results test-instance admin lspping NQA entry(admin, lspping) :testFlag is inactive ,testtype is lspping 1 . Test 1 result The test is finished Send operation times: 3 Receive response times: 3 Completion:success RTD OverThresholds number: 0 Attempts number:1 Drop operation number:0 Disconnect operation number:0 Operation timeout number:0 System busy operation number:0 Connection fail number:0 Operation sequence errors number:0 RTT Stats errors number:0 Destination ip address:3.3.3.9 Min/Max/Average Completion Time: 1/1/1 Sum/Square-Sum Completion Time: 3/3 Last Good Probe Time: 2007-1-30 15:32:56.1 Lost packet ratio:0%
- 配置每天上午10：00开始测试
[~DeviceA-nqa-admin-lspping] stop [*DeviceA-nqa-admin-lspping] start daily 10:00:00 to 10:30:00 [*DeviceA-nqa-admin-lspping] commit
配置文件
DeviceA的配置文件
# sysname DeviceA # mpls lsr-id 1.1.1.9 # mpls # mpls ldp # interface GigabitEthernet0/1/0 undo shutdown ip address 10.1.1.1 255.255.255.0 mpls mpls ldp # interface LoopBack1 ip address 1.1.1.9 255.255.255.255 # ospf 1 area 0.0.0.0 network 10.1.1.0 0.0.0.255 network 1.1.1.9 0.0.0.0 # nqa test-instance admin lspping test-type lspping destination-address ipv4 3.3.3.9 lsp-masklen 32 start daily 10:00:00 to 10:30:00 # return
DeviceB的配置文件
# sysname DeviceB # mpls lsr-id 2.2.2.9 # mpls # mpls ldp # interface GigabitEthernet0/1/0 undo shutdown ip address 10.1.1.2 255.255.255.0 mpls mpls ldp # interface GigabitEthernet0/2/0 undo shutdown ip address 10.2.1.1 255.255.255.0 mpls mpls ldp # interface LoopBack1 ip address 2.2.2.9 255.255.255.255 # ospf 1 area 0.0.0.0 network 2.2.2.9 0.0.0.0 network 10.1.1.0 0.0.0.255 network 10.2.1.0 0.0.0.255 # return
DeviceC的配置文件
# sysname DeviceC # mpls lsr-id 3.3.3.9 # mpls # mpls ldp # interface GigabitEthernet0/1/0 undo shutdown ip address 10.2.1.2 255.255.255.0 mpls mpls ldp # interface LoopBack1 ip address 3.3.3.9 255.255.255.255 # ospf 1 area 0.0.0.0 network 3.3.3.9 0.0.0.0 network 10.2.1.0 0.0.0.255 # return
