配置UDP Jitter测试示例

S9300, S9300X V200R019C10 配置指南-网络管理与监控

本文档介绍了网络管理与监控的配置，具体包括SNMP配置、RMON配置、RMON2配置、LLDP配置、性能管理配置、iPCA配置、NQA配置、业务诊断配置、镜像配置、报文捕获配置、分流配置、NetStream配置、sFlow配置、TWAMP Light配置、NETCONF配置、eMDI配置和智能运维配置。

评分并提供意见反馈 :

华为采用机器翻译与人工审校相结合的方式将此文档翻译成不同语言，希望能帮助您更容易理解此文档的内容。请注意：即使是最好的机器翻译，其准确度也不及专业翻译人员的水平。华为对于翻译的准确性不承担任何责任，并建议您参考英文文档（已提供链接）。

配置UDP Jitter测试示例

组网需求

如图6-37所示。使用UDP Jitter测试SwitchA与SwitchC之间传送报文的抖动时间。

图6-37 Jitter测试组网图

配置思路

采用如下思路进行UDP Jitter测试的配置：

SwitchA作为NQA客户端，SwitchC作为NQA服务器端。
在NQA服务器上配置侦听服务类型和侦听端口号。
在NQA客户端配置UDP Jitter类型的NQA测试例。

操作步骤

配置各接口的IP地址并配置交换机之间路由可达

# 配置SwitchA。

<Quidway> system-view
[Quidway] sysname SwitchA
[SwitchA] vlan 100
[SwitchA-vlan100] quit
[SwitchA] interface gigabitethernet 1/0/1
[SwitchA-GigabitEthernet1/0/1] port hybrid pvid vlan 100
[SwitchA-GigabitEthernet1/0/1] port hybrid untagged vlan 100
[SwitchA-GigabitEthernet1/0/1] quit
[SwitchA] interface vlanif 100
[SwitchA-Vlanif100] ip address 10.1.1.1 24
[SwitchA-Vlanif100] quit
[SwitchA] ip route-static 10.2.1.0 255.255.255.0 10.1.1.2

# 配置SwitchB。

<Quidway> system-view
[Quidway] sysname SwitchB
[SwitchB] vlan 100
[SwitchB-vlan100] quit
[SwitchB] vlan 110
[SwitchB-vlan110] quit
[SwitchB] interface gigabitethernet 1/0/1
[SwitchB-GigabitEthernet1/0/1] port hybrid pvid vlan 100
[SwitchB-GigabitEthernet1/0/1] port hybrid untagged vlan 100
[SwitchB-GigabitEthernet1/0/1] quit
[SwitchB] interface vlanif 100
[SwitchB-Vlanif100] ip address 10.1.1.2 24
[SwitchB-Vlanif100] quit
[SwitchB] interface gigabitethernet 1/0/2
[SwitchB-GigabitEthernet1/0/2] port hybrid pvid vlan 110
[SwitchB-GigabitEthernet1/0/2] port hybrid untagged vlan 110
[SwitchB-GigabitEthernet1/0/2] quit
[SwitchB] interface vlanif 110
[SwitchB-Vlanif110] ip address 10.2.1.1 24
[SwitchB-Vlanif110] quit

# 配置SwitchC。

<Quidway> system-view
[Quidway] sysname SwitchC
[SwitchC] vlan 110
[SwitchC-vlan110] quit
[SwitchC] interface gigabitethernet 1/0/1
[SwitchC-GigabitEthernet1/0/1] port hybrid pvid vlan 110
[SwitchC-GigabitEthernet1/0/1] port hybrid untagged vlan 110
[SwitchC-GigabitEthernet1/0/1] quit
[SwitchC] interface vlanif 110
[SwitchC-Vlanif110] ip address 10.2.1.2 24
[SwitchC-Vlanif110] quit
[SwitchC] ip route-static 10.1.1.0 255.255.255.0 10.2.1.1

在SwitchC上配置NQA服务器
# 配置NQA服务器UDP侦听的IP地址和端口号。
```
[SwitchC] nqa-server udpecho 10.2.1.2 9000
```

配置SwitchA

# 使能NQA客户端，配置UDP Jitter类型的NQA测试例。

[SwitchA] nqa test-instance admin jitter
[SwitchA-nqa-admin-jitter] test-type jitter
[SwitchA-nqa-admin-jitter] destination-address ipv4 10.2.1.2
[SwitchA-nqa-admin-jitter] destination-port 9000

启动测试
```
[SwitchA-nqa-admin-jitter] start now
```

查看测试结果

[SwitchA-nqa-admin-jitter] display nqa results test-instance admin jitter

 NQA entry(admin, jitter) :testflag is inactive ,testtype is jitter             
  1 . Test 1 result   The test is finished                                      
   SendProbe:60                         ResponseProbe:60                        
   Completion:success                   RTD OverThresholds number:0             
   OWD OverThresholds SD number:0       OWD OverThresholds DS number:0          
   Min/Max/Avg/Sum RTT:2/9/2/133        RTT Square Sum:347                      
   NumOfRTT:60                          Drop operation number:0                 
   Operation sequence errors number:0   RTT Stats errors number:0               
   System busy operation number:0       Operation timeout number:0              
   Min Positive SD:1                    Min Positive DS:1                       
   Max Positive SD:7                    Max Positive DS:1                       
   Positive SD Number:8                 Positive DS Number:4                    
   Positive SD Sum:14                   Positive DS Sum:4                       
   Positive SD Square Sum:56            Positive DS Square Sum:4                
   Min Negative SD:1                    Min Negative DS:1                       
   Max Negative SD:6                    Max Negative DS:1                       
   Negative SD Number:9                 Negative DS Number:5                    
   Negative SD Sum:14                   Negative DS Sum:5                       
   Negative SD Square Sum:44            Negative DS Square Sum:5                
   Min Delay SD:1                       Min Delay DS:0                          
   Avg Delay SD:1                       Avg Delay DS:0                          
   Max Delay SD:4                       Max Delay DS:4                          
   Delay SD Square Sum:75               Delay DS Square Sum:22                  
   Packet Loss SD:0                     Packet Loss DS:0                        
   Packet Loss Unknown:0                Average of Jitter:1                     
   Average of Jitter SD:1               Average of Jitter DS:1                  
   Jitter out value:0.3257526           Jitter in value:0.1015234               
   NumberOfOWD:60                       Packet Loss Ratio: 0%                   
   OWD SD Sum:63                        OWD DS Sum:10                           
   ICPIF value: 0                       MOS-CQ value: 0                         
   TimeStamp unit: ms                   Packet Rewrite Number: 0                
   Packet Rewrite Ratio: 0%             Packet Disorder Number: 0               
   Packet Disorder Ratio: 0%            Fragment-disorder Number: 0             
   Fragment-disorder Ratio: 0%          Jitter OverThresholds SD number:0       
   Jitter OverThresholds DS number:0    OverallOverThresholds number:0    
   Start time: 2014-09-01 10:47:57+08:00                                                                                            
   End time: 2014-09-01 10:48:01+08:00

配置文件

SwitchA的配置文件

#
sysname SwitchA
#
vlan batch 100
#
interface Vlanif100
 ip address 10.1.1.1 255.255.255.0
#
interface GigabitEthernet1/0/1
 port hybrid pvid vlan 100
 port hybrid untagged vlan 100
#
ip route-static 10.2.1.0 255.255.255.0 10.1.1.2
#
nqa test-instance admin jitter
 test-type jitter
 destination-address ipv4 10.2.1.2
 destination-port 9000
#
return

SwitchB的配置文件

#
sysname SwitchB
#
vlan batch 100 110
#
interface Vlanif100
 ip address 10.1.1.2 255.255.255.0
#
interface Vlanif110
 ip address 10.2.1.1 255.255.255.0
#
interface GigabitEthernet1/0/1
 port hybrid pvid vlan 100
 port hybrid untagged vlan 100
#
interface GigabitEthernet1/0/2
 port hybrid pvid vlan 110
 port hybrid untagged vlan 110
#
return

SwitchC的配置文件

#
sysname SwitchC
#
vlan batch 110
#
interface Vlanif110
 ip address 10.2.1.2 255.255.255.0
#
interface GigabitEthernet1/0/1
 port hybrid pvid vlan 110
 port hybrid untagged vlan 110
#
nqa-server udpecho 10.2.1.2 9000
#
ip route-static 10.1.1.0 255.255.255.0 10.2.1.1
#
return

组网需求
配置思路

翻译

English

下载文档

更新时间：2022-05-20

文档编号：EDOC1100127082

浏览量：70638

下载量：168

平均得分:

本文档适用于这些产品

数字签名

数字签名验证工具

企业业务网站

华为云网站

运营商网络业务网站

消费者业务网站

集团网站

组网需求

配置思路

操作步骤

配置文件

相关版本

相关文档

数字签名