配置BGP方式VPWS FRR示例-CE对称接入

NetEngine 8000 X V800R012C00SPC300 配置指南 - VPN 04

评分并提供意见反馈 :

华为采用机器翻译与人工审校相结合的方式将此文档翻译成不同语言，希望能帮助您更容易理解此文档的内容。请注意：即使是最好的机器翻译，其准确度也不及专业翻译人员的水平。华为对于翻译的准确性不承担任何责任，并建议您参考英文文档（已提供链接）。

CE对称接入BGP方式的VPWS FRR，两端的CE之间有两条通信路径。

组网需求

如图9-31所示，CE1双归接入PE1和PE2，CE2双归接入PE3和PE4，PE1和PE3之间配置主用BGP方式VPWS，PE2和PE4之间配置备用BGP方式VPWS，因此主用路径为：CE1->PE1->PE3->CE2。当主用路径发生故障时，VPWS的流量能够快速切换到备份路径CE1->PE2->PE4->CE2上。

图9-31 配置BGP方式VPWS FRR示例组网图-CE对称接入

本示例中interface1，sub-interface1.1，inerface2分别代表GE1/0/0，GE1/0/0.1，GE2/0/0。

配置思路

采用如下的思路配置BGP方式VPWS FRR示例-CE对称接入的基本功能：

在骨干网相关设备上配置路由协议实现互通，并使能MPLS基本功能和LDP功能。
使能BGP对等体交换VPWS的功能。
在PE上使能MPLS L2VPN功能，并创建两条CE1到CE2的BGP方式VPWS远程连接。
在PE上配置AC OAM检测和通告功能，并使能OAM Mapping功能。

数据准备

为完成此配置例，需准备如下的数据：

BGP的AS号。
PE上MPLS-L2VPN实例名。
PE上MPLS-L2VPN实例的RD、VPN-Target。
在PE上需要配置的CE名称及ID。

操作步骤

配置IP地址

# 配置CE1。

<HUAWEI> system-view

[~HUAWEI] sysname CE1

[*HUAWEI] commit

[~CE1] vlan 10

[*CE1-vlan10] quit

[*CE1] interface gigabitethernet 1/0/0

[*CE1-GigabitEthernet1/0/0] portswitch

[*CE1-GigabitEthernet1/0/0] port trunk allow-pass vlan 10

[*CE1-GigabitEthernet1/0/0] quit

[*CE1] interface gigabitethernet 2/0/0

[*CE1-GigabitEthernet2/0/0] portswitch

[*CE1-GigabitEthernet2/0/0] port trunk allow-pass vlan 10

[*CE1-GigabitEthernet2/0/0] quit

[*CE1] interface vlanif 10

[*CE1-Vlanif10] ip address 10.1.1.1 24

[*CE1-Vlanif10] quit

[*CE1] cfm enable

[*CE1] cfm md md1

[*CE1-md-md1] ma ma1

[*CE1-md-md1-ma-ma1] map vlan 10

[*CE1-md-md1-ma-ma1] mep mep-id 2 interface GigabitEthernet1/0/0 outward

[*CE1-md-md1-ma-ma1] mep ccm-send mep-id 2 enable

[*CE1-md-md1-ma-ma1] remote-mep mep-id 1

[*CE1-md-md1-ma-ma1] remote-mep ccm-receive mep-id 1 enable

[*CE1-md-md1-ma-ma1] quit

[*CE1-md-md1] quit

[*CE1] cfm md md2

[*CE1-md-md2] ma ma2

[*CE1-md-md2-ma-ma2] map vlan 10

[*CE1-md-md2-ma-ma2] mep mep-id 4 interface gigabitethernet2/0/0 outward

[*CE1-md-md2-ma-ma2] mep ccm-send mep-id 4 enable

[*CE1-md-md2-ma-ma2] remote-mep mep-id 3

[*CE1-md-md2-ma-ma2] remote-mep ccm-receive mep-id 3 enable

[*CE1-md-md2-ma-ma2] quit

[*CE1-md-md2] quit

[*CE1] commit

# 配置CE2。

<HUAWEI> system-view

[~HUAWEI] sysname CE2

[*HUAWEI] commit

[~CE2] vlan 10

[*CE2-vlan10] quit

[*CE2] interface gigabitethernet 1/0/0

[*CE2-GigabitEthernet1/0/0] portswitch

[*CE2-GigabitEthernet1/0/0] port trunk allow-pass vlan 10

[*CE2-GigabitEthernet1/0/0] quit

[*CE2] interface gigabitethernet 2/0/0

[*CE2-GigabitEthernet2/0/0] portswitch

[*CE2-GigabitEthernet2/0/0] port trunk allow-pass vlan 10

[*CE2-GigabitEthernet2/0/0] quit

[*CE2] interface vlanif 10

[*CE2-Vlanif10] ip address 10.1.1.2 24

[*CE2-Vlanif10] quit

[*CE2] cfm enable

[*CE2] cfm md md1

[*CE2-md-md1] ma ma1

[*CE2-md-md1-ma-ma1] map vlan 10

[*CE2-md-md1-ma-ma1] mep mep-id 2 interface GigabitEthernet1/0/0 outward

[*CE2-md-md1-ma-ma1] mep ccm-send mep-id 2 enable

[*CE2-md-md1-ma-ma1] remote-mep mep-id 1

[*CE2-md-md1-ma-ma1] remote-mep ccm-receive mep-id 1 enable

[*CE2-md-md1-ma-ma1] quit

[*CE2-md-md1] quit

[*CE2] cfm md md2

[*CE2-md-md2] ma ma2

[*CE2-md-md2-ma-ma2] map vlan 10

[*CE2-md-md2-ma-ma2] mep mep-id 4 interface GigabitEthernet1/0/0 outward

[*CE2-md-md2-ma-ma2] mep ccm-send mep-id 4 enable

[*CE2-md-md2-ma-ma2] remote-mep mep-id 3

[*CE2-md-md2-ma-ma2] remote-mep ccm-receive mep-id 3 enable

[*CE2-md-md2-ma-ma2] quit

[*CE2-md-md2] quit

[*CE2] commit

# 配置PE1。

<HUAWEI> system-view

[~HUAWEI] sysname PE1

[*HUAWEI] commit

[~PE1] interface gigabitethernet 1/0/0.1

[*PE1-GigabitEthernet1/0/0.1] vlan-type dot1q 10

[*PE1-GigabitEthernet1/0/0.1] quit

[*PE1] interface loopback 1

[*PE1-LoopBack1] ip address 1.1.1.9 32

[*PE1-LoopBack1] quit

[*PE1] interface gigabitethernet 2/0/0

[*PE1-GigabitEthernet2/0/0] ip address 192.168.1.1 24

[*PE1-GigabitEthernet2/0/0] quit

[*PE1] commit

# 配置PE2。

<HUAWEI> system-view

[~HUAWEI] sysname PE2

[*HUAWEI] commit

[~PE2] interface gigabitethernet 1/0/0.1

[*PE2-GigabitEthernet1/0/0.1] vlan-type dot1q 10

[*PE2-GigabitEthernet1/0/0.1] quit

[*PE2] interface loopback 1

[*PE2-LoopBack1] ip address 2.2.2.9 32

[*PE2-LoopBack1] quit

[*PE2] interface gigabitethernet 2/0/0

[*PE2-GigabitEthernet2/0/0] ip address 192.168.10.1 24

[*PE2-GigabitEthernet2/0/0] quit

[*PE2] commit

# 配置PE3。

<HUAWEI> system-view

[~HUAWEI] sysname PE3

[*HUAWEI] commit

[~PE3] interface gigabitethernet 1/0/0.1

[*PE3-GigabitEthernet1/0/0.1] vlan-type dot1q 10

[*PE3-GigabitEthernet1/0/0.1] quit

[*PE3] interface loopback 1

[*PE3-LoopBack1] ip address 3.3.3.9 24

[*PE3-LoopBack1] quit

[*PE3] interface gigabitethernet 2/0/0

[*PE3-GigabitEthernet2/0/0] ip address 192.168.1.2 24

[*PE3-GigabitEthernet2/0/0] quit

[*PE3] commit

# 配置PE4。

<HUAWEI> system-view

[~HUAWEI] sysname PE4

[*HUAWEI] commit

[~PE4] interface gigabitethernet 1/0/0.1

[*PE4-GigabitEthernet1/0/0.1] vlan-type dot1q 10

[*PE4-GigabitEthernet1/0/0.1] quit

[*PE4] interface loopback 1

[*PE4-LoopBack1] ip address 4.4.4.9 24

[*PE4-LoopBack1] quit

[*PE4] interface gigabitethernet 2/0/0

[*PE4-GigabitEthernet2/0/0] ip address 192.168.10.2 24

[*PE4-GigabitEthernet2/0/0] quit

[*PE4] commit

配置IGP，本示例使用OSPF

# 配置PE1。

[~PE1] ospf 1

[*PE1-ospf-1] area 0

[*PE1-ospf-1-area-0.0.0.0] network 1.1.1.9 0.0.0.0

[*PE1-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255

[*PE1-ospf-1-area-0.0.0.0] quit

[*PE1-ospf-1] quit

[*PE1] commit

# 配置PE2。

[~PE2] ospf 1

[*PE2-ospf-1] area 0

[*PE2-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0

[*PE2-ospf-1-area-0.0.0.0] network 192.168.10.0 0.0.0.255

[*PE2-ospf-1-area-0.0.0.0] quit

[*PE2-ospf-1] quit

[*PE2] commit

# 配置PE3。

[~PE3] ospf 1

[*PE3-ospf-1] area 0

[*PE3-ospf-1-area-0.0.0.0] network 3.3.3.9 0.0.0.0

[*PE3-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255

[*PE3-ospf-1-area-0.0.0.0] quit

[*PE3-ospf-1] quit

[*PE3] commit

# 配置PE4。

[~PE4] ospf 1

[*PE4-ospf-1] area 0

[*PE4-ospf-1-area-0.0.0.0] network 4.4.4.9 0.0.0.0

[*PE4-ospf-1-area-0.0.0.0] network 192.168.10.0 0.0.0.255

[*PE4-ospf-1-area-0.0.0.0] quit

[*PE4-ospf-1] quit

[*PE4] commit

使能MPLS功能，建立LSP隧道

# 配置PE1。

[~PE1] mpls lsr-id 1.1.1.9

[*PE1] mpls

[*PE1-mpls] quit

[*PE1] mpls ldp

[*PE1-mpls-ldp] quit

[*PE1] interface gigabitethernet 2/0/0

[*PE1-GigabitEthernet2/0/0] mpls

[*PE1-GigabitEthernet2/0/0] mpls ldp

[*PE1-GigabitEthernet2/0/0] quit

[*PE1] commit

# 配置PE2。

[~PE2] mpls lsr-id 2.2.2.9

[*PE2] mpls

[*PE2-mpls] quit

[*PE2] mpls ldp

[*PE2-mpls-ldp] quit

[*PE2] interface gigabitethernet 2/0/0

[*PE2-GigabitEthernet2/0/0] mpls

[*PE2-GigabitEthernet2/0/0] mpls ldp

[*PE2-GigabitEthernet2/0/0] quit

[*PE2] commit

# 配置PE3。

[~PE3] mpls lsr-id 3.3.3.9

[*PE3] mpls

[*PE3-mpls] quit

[*PE3] mpls ldp

[*PE3-mpls-ldp] quit

[*PE3] interface gigabitethernet 2/0/0

[*PE3-GigabitEthernet2/0/0] mpls

[*PE3-GigabitEthernet2/0/0] mpls ldp

[*PE3-GigabitEthernet2/0/0] quit

[*PE3] commit

# 配置PE4。

[~PE4] mpls lsr-id 4.4.4.9

[*PE4] mpls

[*PE4-mpls] quit

[*PE4] mpls ldp

[*PE4-mpls-ldp] quit

[*PE4] interface gigabitethernet 2/0/0

[*PE4-GigabitEthernet2/0/0] mpls

[*PE4-GigabitEthernet2/0/0] mpls ldp

[*PE4-GigabitEthernet2/0/0] quit

[*PE4] commit

使能BGP对等体交换VPWS信息的功能

# 配置PE1。

[~PE1] bgp 100

[*PE1-bgp] peer 3.3.3.9 as-number 100

[*PE1-bgp] peer 3.3.3.9 connect-interface loopback 1

[*PE1-bgp] l2vpn-ad-family

[*PE1-bgp-af-l2vpn-ad] peer 3.3.3.9 enable

[*PE1-bgp-af-l2vpn-ad] peer 3.3.3.9 signaling vpws

[*PE1-bgp-af-l2vpn-ad] quit

[*PE1-bgp] quit

[*PE1] commit

# 配置PE3。

[~PE3] bgp 100

[*PE3-bgp] peer 1.1.1.9 as-number 100

[*PE3-bgp] peer 1.1.1.9 connect-interface loopback 1

[*PE3-bgp] l2vpn-ad-family

[*PE3-bgp-af-l2vpn-ad] peer 1.1.1.9 enable

[*PE3-bgp-af-l2vpn-ad] peer 1.1.1.9 signaling vpws

[*PE3-bgp-af-l2vpn-ad] quit

[*PE3-bgp] quit

[*PE3] commit

# 配置PE2。

[~PE2] bgp 100

[*PE2-bgp] peer 4.4.4.9 as-number 100

[*PE2-bgp] peer 4.4.4.9 connect-interface loopback 1

[*PE2-bgp] l2vpn-ad-family

[*PE2-bgp-af-l2vpn-ad] peer 4.4.4.9 enable

[*PE2-bgp-af-l2vpn-ad] peer 4.4.4.9 signaling vpws

[*PE2-bgp-af-l2vpn-ad] quit

[*PE2-bgp] quit

[*PE2] commit

# 配置PE4。

[~PE4] bgp 100

[*PE4-bgp] peer 2.2.2.9 as-number 100

[*PE4-bgp] peer 2.2.2.9 connect-interface loopback 1

[*PE4-bgp] l2vpn-ad-family

[*PE4-bgp-af-l2vpn-ad] peer 2.2.2.9 enable

[*PE4-bgp-af-l2vpn-ad] peer 2.2.2.9 signaling vpws

[*PE4-bgp-af-l2vpn-ad] quit

[*PE4-bgp] quit

[*PE4] commit

在配置BGP方式VPWS远程连接

# 配置PE1。

[~PE1] mpls l2vpn

[*PE1-l2vpn] quit

[*PE1] mpls l2vpn vpn1 encapsulation vlan control-word

[*PE1-mpls-l2vpn-vpn1] route-distinguisher 100:1

[*PE1-mpls-l2vpn-vpn1] vpn-target 200:1 both

[*PE1-mpls-l2vpn-vpn1] ce ce1 id 1 range 10

[*PE1-mpls-l2vpn-vpn1-ce-ce1] connection ce-offset 3 interface gigabitethernet 1/0/0.1

[*PE1-mpls-l2vpn-vpn1-ce-ce1] quit

[*PE1-mpls-l2vpn-vpn1] quit

[*PE1] commit

# 配置PE2。

[~PE2] mpls l2vpn

[*PE2-l2vpn] quit

[*PE2] mpls l2vpn vpn1 encapsulation vlan control-word

[*PE2-mpls-l2vpn-vpn1] route-distinguisher 100:1

[*PE2-mpls-l2vpn-vpn1] vpn-target 200:1 both

[*PE2-mpls-l2vpn-vpn1] ce ce2 id 2 range 10

[*PE2-mpls-l2vpn-vpn1-ce-ce2] connection ce-offset 4 interface gigabitethernet 1/0/0.1

[*PE2-mpls-l2vpn-vpn1-ce-ce2] quit

[*PE2-mpls-l2vpn-vpn1] quit

[*PE2] commit

# 配置PE3。

[~PE3] mpls l2vpn

[*PE3-l2vpn] quit

[*PE3] mpls l2vpn vpn1 encapsulation vlan control-word

[*PE3-mpls-l2vpn-vpn1] route-distinguisher 100:1

[*PE3-mpls-l2vpn-vpn1] vpn-target 200:1 both

[*PE3-mpls-l2vpn-vpn1] ce ce3 id 3 range 10

[*PE3-mpls-l2vpn-vpn1-ce-ce3] connection ce-offset 1 interface gigabitethernet 1/0/0.1

[*PE3-mpls-l2vpn-vpn1-ce-ce3] quit

[*PE3-mpls-l2vpn-vpn1] quit

[*PE3] commit

# 配置PE4。

[~PE4] mpls l2vpn

[*PE4-l2vpn] quit

[*PE4] mpls l2vpn vpn1 encapsulation vlan control-word

[*PE4-mpls-l2vpn-vpn1] route-distinguisher 100:1

[*PE4-mpls-l2vpn-vpn1] vpn-target 200:1 both

[*PE4-mpls-l2vpn-vpn1] ce ce4 id 4 range 10

[*PE4-mpls-l2vpn-vpn1-ce-ce4] connection ce-offset 2 interface gigabitethernet 1/0/0.1

[*PE4-mpls-l2vpn-vpn1-ce-ce4] quit

[*PE4-mpls-l2vpn-vpn1] quit

[*PE4] commit

配置BFD检测PW。

# 配置PE1。

[~PE1] bfd

[*PE1-bfd] quit

[*PE1] bfd 1to3 bind pw interface gigabitethernet 1/0/0.1

[*PE1-bfd-lsp-session-1to3] discriminator local 13

[*PE1-bfd-lsp-session-1to3] discriminator remote 31

[*PE1-bfd-lsp-session-1to3] quit

[*PE1] commit

# 配置PE3。

[~PE3] bfd

[*PE3-bfd] quit

[*PE3] bfd 3to1 bind pw interface gigabitethernet 1/0/0.1

[*PE3-bfd-lsp-session-3to1] discriminator local 31

[*PE3-bfd-lsp-session-3to1] discriminator remote 13

[*PE3-bfd-lsp-session-3to1] quit

[*PE3] commit

# 配置PE2。

[~PE2] bfd

[*PE2-bfd] quit

[*PE2] bfd 2to4 bind pw interface gigabitethernet 1/0/0.1

[*PE2-bfd-lsp-session-2to4] discriminator local 24

[*PE2-bfd-lsp-session-2to4] discriminator remote 42

[*PE2-bfd-lsp-session-2to4] quit

[*PE2] commit

# 配置PE4。

[~PE4] bfd

[*PE4-bfd] quit

[*PE4] bfd 4to2 bind pw interface gigabitethernet 1/0/0.1

[*PE4-bfd-lsp-session-4to2] discriminator local 42

[*PE4-bfd-lsp-session-4to2] discriminator remote 24

[*PE4-bfd-lsp-session-4to2] quit

[*PE4] commit

配置OAM Mapping功能。

# 配置PE1。

[~PE1] cfm enable

[*PE1] cfm md md1

[*PE1-md-md1] ma ma1

[*PE1-md-md1-ma-ma1] map vlan 10

[*PE1-md-md1-ma-ma1] mep mep-id 1 interface GigabitEthernet1/0/0.1 outward

[*PE1-md-md1-ma-ma1] mep ccm-send mep-id 1 enable

[*PE1-md-md1-ma-ma1] remote-mep mep-id 2

[*PE1-md-md1-ma-ma1] remote-mep ccm-receive mep-id 2 enable

[*PE1-md-md1-ma-ma1] quit

[*PE1-md-md1] quit

[*PE1] interface gigabitethernet1/0/0.1

[*PE1-GigabitEthernet1/0/0.1] mpls l2vpn oam-mapping 1ag md md1 ma ma1

[*PE1-GigabitEthernet1/0/0.1] quit

[*PE1] commit

# 配置PE2。

[~PE2] cfm enable

[*PE2] cfm md md2

[*PE2-md-md2] ma ma2

[*PE2-md-md2-ma-ma2] map vlan 10

[*PE2-md-md2-ma-ma2] mep mep-id 3 interface GigabitEthernet1/0/0.1 outward

[*PE2-md-md2-ma-ma2] mep ccm-send mep-id 3 enable

[*PE2-md-md2-ma-ma2] remote-mep mep-id 4

[*PE2-md-md2-ma-ma2] remote-mep ccm-receive mep-id 4 enable

[*PE2-md-md2-ma-ma2] quit

[*PE2-md-md2] quit

[*PE2] interface gigabitethernet1/0/0.1

[*PE2-GigabitEthernet1/0/0.1] mpls l2vpn oam-mapping 1ag md md2 ma ma2

[*PE2-GigabitEthernet1/0/0.1] quit

[*PE2] commit

# 配置PE3。

[~PE3] cfm enable

[*PE3] cfm md md1

[*PE3-md-md1] ma ma1

[*PE3-md-md1-ma-ma1] map vlan 10

[*PE3-md-md1-ma-ma1] mep mep-id 1 interface GigabitEthernet1/0/0.1 outward

[*PE3-md-md1-ma-ma1] mep ccm-send mep-id 1 enable

[*PE3-md-md1-ma-ma1] remote-mep mep-id 2

[*PE3-md-md1-ma-ma1] remote-mep ccm-receive mep-id 2 enable

[*PE3-md-md1-ma-ma1] quit

[*PE3-md-md1] quit

[*PE3] interface gigabitethernet1/0/0.1

[*PE3-GigabitEthernet1/0/0.1] mpls l2vpn oam-mapping 1ag md md1 ma ma1

[*PE3-GigabitEthernet1/0/0.1] quit

[*PE3] commit

# 配置PE4。

[~PE4] cfm enable

[*PE4] cfm md md2

[*PE4-md-md2] ma ma2

[*PE4-md-md2-ma-ma2] map vlan 10

[*PE4-md-md2-ma-ma2] mep mep-id 3 interface GigabitEthernet1/0/0.1 outward

[*PE4-md-md2-ma-ma2] mep ccm-send mep-id 3 enable

[*PE4-md-md2-ma-ma2] remote-mep mep-id 4

[*PE4-md-md2-ma-ma2] remote-mep ccm-receive mep-id 4 enable

[*PE4-md-md2-ma-ma2] quit

[*PE4-md-md2] quit

[*PE4] interface gigabitethernet1/0/0.1

[*PE4-GigabitEthernet1/0/0.1] mpls l2vpn oam-mapping 1ag md md2 ma ma2

[*PE4-GigabitEthernet1/0/0.1] quit

[*PE4] commit

验证配置结果

完成上述配置后，执行display mpls l2vpn connection interface命令，可以看到建立了BGP方式VPWS连接。以PE1的显示为例：

[~PE1] display mpls l2vpn connection interface gigabitethernet 1/0/0.1

conn-type: remote
     local vc state:             up
     remote vc state:            up
     local ce-id:                1
     local ce name:              ce1
     remote ce-id:               3
     intf(state,encap):          GigabitEthernet1/0/0.1(up,vlan)
     peer id:                    3.3.3.9
     route-distinguisher:        100:1
     local vc label:             294931
     remote vc label:            294929
     tunnel policy:              default 
     CKey:                       129
     NKey:                       268435580
     primary or secondary:       primary
     forward entry exist or not: true
     forward entry active or not:true
     manual fault set or not:    not set 
     AC OAM state:               up 
     BFD for PW session index:   -- 
     BFD for PW state:           enable 
     BFD for LSP state:          up
     Local C bit is set 
     Remote C bit is set 
     tunnel type:                ldp
     tunnel id:                  0x0000000001004c4b42

CE1与CE2能够相互Ping通。

[~CE1] ping 10.1.1.2

  PING 10.1.1.2: 56  data bytes, press CTRL_C to break
    Reply from 10.1.1.2: bytes=56 Sequence=1 ttl=255 time=2 ms
    Reply from 10.1.1.2: bytes=56 Sequence=2 ttl=255 time=1 ms
    Reply from 10.1.1.2: bytes=56 Sequence=3 ttl=255 time=1 ms
    Reply from 10.1.1.2: bytes=56 Sequence=4 ttl=255 time=1 ms
    Reply from 10.1.1.2: bytes=56 Sequence=5 ttl=255 time=1 ms

  --- 10.1.1.2 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 1/1/2 ms

配置文件

CE1的配置文件

#
sysname CE1
#
vlan batch 10
#
cfm enable
#
interface Vlanif10
 ip address 10.1.1.1 255.255.255.0
#               
interface GigabitEthernet1/0/0
 portswitch     
 undo shutdown  
 port trunk allow-pass vlan 10
#               
interface GigabitEthernet2/0/0
 portswitch     
 undo shutdown  
 port trunk allow-pass vlan 10
#               
cfm md md1       
 ma ma1          
  map vlan 10    
  mep mep-id 2 interface GigabitEthernet1/0/0 outward
  mep ccm-send mep-id 2 enable
  remote-mep mep-id 1
  remote-mep ccm-receive mep-id 1 enable
#               
cfm md md2      
 ma ma2         
  map vlan 10    
  mep mep-id 4 interface GigabitEthernet2/0/0 outward
  mep ccm-send mep-id 4 enable
  remote-mep mep-id 3
  remote-mep ccm-receive mep-id 3 enable
#               
return

CE2的配置文件

#
sysname CE2
#
vlan batch 10
#
cfm enable
#
interface Vlanif10
 ip address 10.1.1.2 255.255.255.0
#               
interface GigabitEthernet1/0/0
 portswitch     
 undo shutdown  
 port trunk allow-pass vlan 10
#               
interface GigabitEthernet2/0/0
 portswitch     
 undo shutdown  
 port trunk allow-pass vlan 10
#               
cfm md md1       
 ma ma1          
  map vlan 10    
  mep mep-id 2 interface GigabitEthernet1/0/0 outward
  mep ccm-send mep-id 2 enable
  remote-mep mep-id 1
  remote-mep ccm-receive mep-id 1 enable
#               
cfm md md2      
 ma ma2         
  map vlan 10    
  mep mep-id 4 interface GigabitEthernet2/0/0 outward
  mep ccm-send mep-id 4 enable
  remote-mep mep-id 3
  remote-mep ccm-receive mep-id 3 enable
#               
return

PE1的配置文件

#
sysname PE1
#
cfm enable
#
bfd
#
mpls lsr-id 1.1.1.9
#
mpls
#
mpls l2vpn
#               
mpls ldp        
#               
interface GigabitEthernet1/0/0
 undo shutdown
#               
interface GigabitEthernet1/0/0.1
 vlan-type dot1q 10
 mpls l2vpn oam-mapping 1ag md md1 ma ma1
#               
interface GigabitEthernet2/0/0
 undo shutdown  
 ip address 192.168.1.1 255.255.255.0
 mpls           
 mpls ldp       
#               
interface LoopBack1
 ip address 1.1.1.9 255.255.255.255
#               
mpls l2vpn vpn1 encapsulation vlan control-word
 route-distinguisher 100:1
 vpn-target 200:1 import-extcommunity
 vpn-target 200:1 export-extcommunity
 ce ce1 id 1 range 10 default-offset 0
  connection ce-offset 3 interface GigabitEthernet1/0/0.1
#               
bgp 100         
 peer 3.3.3.9 as-number 100
 peer 3.3.3.9 connect-interface LoopBack1
 #              
 ipv4-family unicast
  undo synchronization
  peer 3.3.3.9 enable
 #              
 l2vpn-ad-family
  policy vpn-target
  peer 3.3.3.9 enable
  peer 3.3.3.9 signaling vpws
#               
ospf 1          
 area 0.0.0.0   
  network 1.1.1.9 0.0.0.0
  network 192.168.1.0 0.0.0.255
#               
cfm md md1       
 ma ma1          
  map vlan 10    
  mep mep-id 1 interface GigabitEthernet1/0/0.1 outward
  mep ccm-send mep-id 1 enable
  remote-mep mep-id 2
  remote-mep ccm-receive mep-id 2 enable
#               
return

PE2的配置文件

#
sysname PE2
#
cfm enable
#
bfd
#
mpls lsr-id 2.2.2.9
#
mpls
#
mpls l2vpn
#               
mpls ldp        
#               
interface GigabitEthernet1/0/0
 undo shutdown
#               
interface GigabitEthernet1/0/0.1
 vlan-type dot1q 10
 mpls l2vpn oam-mapping 1ag md md2 ma ma2
#               
interface GigabitEthernet2/0/0
 undo shutdown  
 ip address 192.168.10.1 255.255.255.0
 mpls           
 mpls ldp       
#               
interface LoopBack1
 ip address 2.2.2.9 255.255.255.255
#               
mpls l2vpn vpn1 encapsulation vlan control-word
 route-distinguisher 100:1
 vpn-target 200:1 import-extcommunity
 vpn-target 200:1 export-extcommunity
 ce ce2 id 2 range 10 default-offset 0
  connection ce-offset 4 interface GigabitEthernet1/0/0.1
#               
bgp 100         
 peer 4.4.4.9 as-number 100
 peer 4.4.4.9 connect-interface LoopBack1
 #              
 ipv4-family unicast
  undo synchronization
  peer 4.4.4.9 enable
 #              
 l2vpn-ad-family
  policy vpn-target
  peer 4.4.4.9 enable
  peer 4.4.4.9 signaling vpws
#               
ospf 1          
 area 0.0.0.0   
  network 2.2.2.9 0.0.0.0
  network 192.168.10.0 0.0.0.255
#               
cfm md md2       
 ma ma2          
  map vlan 10    
  mep mep-id 3 interface GigabitEthernet1/0/0.1 outward
  mep ccm-send mep-id 3 enable
  remote-mep mep-id 4
  remote-mep ccm-receive mep-id 4 enable
#               
return

PE3的配置文件

#
sysname PE3
#
cfm enable
#
bfd
#
mpls lsr-id 3.3.3.9
#
mpls
#
mpls l2vpn
#               
mpls ldp        
#               
interface GigabitEthernet1/0/0
 undo shutdown
#               
interface GigabitEthernet1/0/0.1
 vlan-type dot1q 10
 mpls l2vpn oam-mapping 1ag md md1 ma ma1
#               
interface GigabitEthernet2/0/0
 undo shutdown  
 ip address 192.168.1.2 255.255.255.0
 mpls           
 mpls ldp       
#               
interface LoopBack1
 ip address 3.3.3.9 255.255.255.255
#               
mpls l2vpn vpn1 encapsulation vlan control-word
 route-distinguisher 100:1
 vpn-target 200:1 import-extcommunity
 vpn-target 200:1 export-extcommunity
 ce ce3 id 3 range 10 default-offset 0
  connection ce-offset 1 interface GigabitEthernet1/0/0.1
#               
bgp 100         
 peer 1.1.1.9 as-number 100
 peer 1.1.1.9 connect-interface LoopBack1
 #              
 ipv4-family unicast
  undo synchronization
  peer 1.1.1.9 enable
 #              
 l2vpn-ad-family
  policy vpn-target
  peer 1.1.1.9 enable
  peer 1.1.1.9 signaling vpws
#               
ospf 1          
 area 0.0.0.0   
  network 3.3.3.9 0.0.0.0
  network 192.168.1.0 0.0.0.255
#               
cfm md md1       
 ma ma1          
  map vlan 10    
  mep mep-id 1 interface GigabitEthernet1/0/0.1 outward
  mep ccm-send mep-id 1 enable
  remote-mep mep-id 2
  remote-mep ccm-receive mep-id 2 enable
#               
return

PE4的配置文件

#
sysname PE4
#
cfm enable
#
bfd
#
mpls lsr-id 4.4.4.9
#
mpls
#
mpls l2vpn
#               
mpls ldp        
#               
interface GigabitEthernet1/0/0
 undo shutdown
#               
interface GigabitEthernet1/0/0.1
 vlan-type dot1q 10
 mpls l2vpn oam-mapping 1ag md md2 ma ma2
#               
interface GigabitEthernet2/0/0
 undo shutdown  
 ip address 192.168.10.2 255.255.255.0
 mpls           
 mpls ldp       
#               
interface LoopBack1
 ip address 4.4.4.9 255.255.255.255
#               
mpls l2vpn vpn1 encapsulation vlan control-word
 route-distinguisher 100:1
 vpn-target 200:1 import-extcommunity
 vpn-target 200:1 export-extcommunity
 ce ce4 id 4 range 10 default-offset 0
  connection ce-offset 2 interface GigabitEthernet1/0/0.1
#               
bgp 100         
 peer 2.2.2.9 as-number 100
 peer 2.2.2.9 connect-interface LoopBack1
 #              
 ipv4-family unicast
  undo synchronization
  peer 2.2.2.9 enable
 #              
 l2vpn-ad-family
  policy vpn-target
  peer 2.2.2.9 enable
  peer 2.2.2.9 signaling vpws
#               
ospf 1          
 area 0.0.0.0   
  network 4.4.4.9 0.0.0.0
  network 192.168.10.0 0.0.0.255
#               
cfm md md2       
 ma ma2          
  map vlan 10    
  mep mep-id 3 interface GigabitEthernet1/0/0.1 outward
  mep ccm-send mep-id 3 enable
  remote-mep mep-id 4
  remote-mep ccm-receive mep-id 4 enable
#               
return

翻译

English

下载文档

更新时间：2020-06-20

文档编号：EDOC1100143312

浏览量：59886

下载量：127

平均得分:

本文档适用于这些产品

组网需求

配置思路

数据准备

操作步骤

配置文件

相关版本

相关文档