SupportDocumentationSwitchesCampus SwitchS1700&S2700Configuration & CommissioningConfiguration Guide

S1720, S2700, S5700, and S6720 V200R011C10 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring link aggregation, VLANs, Voice VLAN, VLAN mapping, QinQ, GVRP, MAC table, STP/RSTP/MSTP, SEP, and so on.

This document describes the configuration of Ethernet services, including configuring link aggregation, VLANs, Voice VLAN, VLAN mapping, QinQ, GVRP, MAC table, STP/RSTP/MSTP, SEP, and so on.

Example for Configuring Dot1q Termination Sub-interfaces to Implement Inter-VLAN Communication

Example for Configuring Dot1q Termination Sub-interfaces to Implement Inter-VLAN Communication

Networking Requirements

‏‏An enterprise's departments are located on different network segments and use the same services such as Internet access and VoIP. To allow the departments in different VLANs to use the same service, inter-VLAN communication must be implemented.

In the networking example shown in Figure 8-7, both department 1 and department 2 located in different VLANs and network segments need to use the Internet access service, and users in department 1 and department 2 need to communicate with each other.

Figure 8-7  Networking for configuring Dot1q termination sub-interfaces to implement inter-VLAN communication

Configuration Roadmap

The configuration roadmap is as follows.

  1. Configure the ID of the VLAN to which each interface belongs.

  2. Configure Dot1q termination sub-interfaces.

  3. Assign IP addresses to the sub-interfaces.

VLAN termination sub-interfaces cannot be created on a VCMP client.

Procedure

  1. Add the uplink interface of SwitchA to VLAN 10 in tagged mode and the user-side interface to VLAN 10 in untagged mode, and add the uplink interface of SwitchB to VLAN 20 in tagged mode and the user-side interface to VLAN 20 in untagged mode. Configure VLANs on interfaces of SwitchA and SwitchB. 

    <HUAWEI> system-view
[HUAWEI] sysname SwitchA
[SwitchA] vlan batch 10
[SwitchA] interface gigabitethernet0/0/1
[SwitchA-GigabitEthernet0/0/1] port link-type access
[SwitchA-GigabitEthernet0/0/1] port default vlan 10
[SwitchA-GigabitEthernet0/0/1] quit
[SwitchA] interface gigabitethernet0/0/2
[SwitchA-GigabitEthernet0/0/2] port link-type trunk
[SwitchA-GigabitEthernet0/0/2] port trunk allow-pass vlan 10
[SwitchA-GigabitEthernet0/0/2] quit

    <HUAWEI> system-view
[HUAWEI] sysname SwitchB
[SwitchB] vlan batch 20
[SwitchB] interface gigabitethernet0/0/1
[SwitchB-GigabitEthernet0/0/1] port link-type access
[SwitchB-GigabitEthernet0/0/1] port default vlan 20
[SwitchB-GigabitEthernet0/0/1] quit
[SwitchB] interface gigabitethernet0/0/2
[SwitchB-GigabitEthernet0/0/2] port link-type trunk
[SwitchB-GigabitEthernet0/0/2] port trunk allow-pass vlan 20
[SwitchB-GigabitEthernet0/0/2] quit

  2. Configure the interface on the Switch connected to SwitchA.

    # Create and configure the Ethernet sub-interface GE0/0/1.1.

    <HUAWEI> system-view
[HUAWEI] sysname Switch
[Switch] vcmp role silent
[Switch] interface gigabitethernet0/0/1
[Switch-GigabitEthernet0/0/1] port link-type hybrid
[Switch-GigabitEthernet0/0/1] quit
[Switch] interface gigabitethernet0/0/1.1
[Switch-GigabitEthernet0/0/1.1] dot1q termination vid 10
[Switch-GigabitEthernet0/0/1.1] ip address 10.10.10.1 24
[Switch-GigabitEthernet0/0/1.1] arp broadcast enable
[Switch-GigabitEthernet0/0/1.1] quit

  3. Configure the interface on the Switch connected to SwitchB.

    # Create and configure the Ethernet sub-interface GE0/0/2.1.

    [Switch] interface gigabitethernet0/0/2
[Switch-GigabitEthernet0/0/2] port link-type hybrid
[Switch-GigabitEthernet0/0/2] quit
[Switch] interface gigabitethernet 0/0/2.1
[Switch-GigabitEthernet0/0/2.1] dot1q termination vid 20
[Switch-GigabitEthernet0/0/2.1] ip address 10.10.20.1 24
[Switch-GigabitEthernet0/0/2.1] arp broadcast enable
[Switch-GigabitEthernet0/0/2.1] quit

  4. Verify the configuration.

    On PC1 in VLAN 10, set the default gateway address to 10.10.10.1/24, which is the IP address of GE0/0/1.1.

    On PC2 in VLAN 20, set the default gateway address to 10.10.20.1/24, which is the IP address of GE0/0/2.1.

    After the configuration is complete, PC1 in VLAN 10 and PC2 in VLAN 20 can communicate with each other.

Configuration Files

Switch configuration file

#
sysname Switch
#
vcmp role silent
#
interface GigabitEthernet0/0/1
 port link-type hybrid
#
interface GigabitEthernet0/0/1.1
 dot1q termination vid 10
 ip address 10.10.10.1 255.255.255.0
 arp broadcast enable
#
interface GigabitEthernet0/0/2
 port link-type hybrid
#
interface GigabitEthernet0/0/2.1
 dot1q termination vid 20
 ip address 10.10.20.1 255.255.255.0
 arp broadcast enable
#
return

SwitchA configuration file

#
sysname SwitchA
#
vlan batch 10
#
interface GigabitEthernet0/0/1
 port link-type access
 port default vlan 10
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 10
#
return

SwitchB configuration file

#
sysname SwitchB
#
vlan batch 20
#
interface GigabitEthernet0/0/1
 port link-type access
 port default vlan 20
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 20
#
return