S300, S500, S2700, S5700, and S6700 V200R020C10 Configuration Guide - Device Management

S5732-H Service Port Stacking Support

For the cables that can be used as stack cables, see "Cables" in the Hardware Description. Using other cables may cause exceptions in the stack system, for example, frequent error-down events on stack ports.
Any models of the S5732-H series can set up a stack.
The number of stacked switches is recommended to be 2 to 9. In addition, when using iMaster NCE-Campus to manage and maintain a stack, ensure that the stack has no more than four member switches.
A switch supports a maximum of two logical stack ports.
For stacking-supported service ports, some of them can be used as stack ports, whereas some can be used as ordinary service ports.
The rates of physical member ports in a logical stack port must be the same. The rates of physical member ports in different logical stack ports on a device can be different.
The minimum version required by the S5732-H24UM2CC, S5732-H48XUM2CC, and S5732-H48UM2CC is V200R019C10SPC500. In this case, when they set up a stack with a switch of another S5732-H model which acts as the master switch, the master switch must run V200R019C10SPC500 or a later version. Otherwise, the S5732-H24UM2CC, S5732-H48XUM2CC, and S5732-H48UM2CC cannot join the stack.

Table 3-29 S5732-H24S6Q and S5732-H48S6Q Service port stacking support

Port Supporting Stacking	Stack Cable	Rate of a Single Port	Maximum of Stack Member Ports in a Logical Stack Port
40GE/100GE ports on the front panel	1 m, 3 m, and 5 m QSFP+ high-speed copper cables QSFP+ optical module and optical fiber (QSFP-40G-SR-BD optical modules can be used for stack since V200R019C10SPC500.) 10 m QSFP+ AOC cable	40Gbit/s	6
1 m QSFP28 high-speed copper cables (supported in V200R020C00 and later versions, with a license loaded) 10 m QSFP28 AOC cables (supported in V200R020C00 and later versions, with a license loaded) QSFP28 optical module and optical fiber (supported in V200R020C00 and later versions, with a license loaded) 2m QSFP28 dedicated stack cables (supported in V200R020C10 and later versions)	100Gbit/s	6

Port Supporting Stacking

Stack Cable

Rate of a Single Port

Maximum of Stack Member Ports in a Logical Stack Port

40GE/100GE ports on the front panel

1 m, 3 m, and 5 m QSFP+ high-speed copper cables
QSFP+ optical module and optical fiber (QSFP-40G-SR-BD optical modules can be used for stack since V200R019C10SPC500.)
10 m QSFP+ AOC cable

40Gbit/s

1 m QSFP28 high-speed copper cables (supported in V200R020C00 and later versions, with a license loaded)
10 m QSFP28 AOC cables (supported in V200R020C00 and later versions, with a license loaded)
QSFP28 optical module and optical fiber (supported in V200R020C00 and later versions, with a license loaded)

2m QSFP28 dedicated stack cables (supported in V200R020C10 and later versions)

100Gbit/s

Table 3-30 S5732-H24UM2CC and S5732-H48UM2CC Service port stacking support

Port Supporting Stacking	Stack Cable	Rate of a Single Port	Maximum of Stack Member Ports in a Logical Stack Port
MultiGE ports on the front panel	Category 6A or higher network cables (If Category 6 cables are used, ensure that the cables meet requirements of TSB-155.)	10Gbit/s	8
40GE/100GE ports on the front panel	1 m, 3 m, and 5 m QSFP+ high-speed copper cables QSFP+ optical module and optical fiber (QSFP-40G-SR-BD optical modules can be used for stack since V200R019C10SPC500.) 10 m QSFP+ AOC cable	40Gbit/s	2
40GE/100GE ports on the front panel	1 m, 3 m, and 5 m QSFP28 high-speed copper cables 10 m QSFP28 AOC cables QSFP28 optical module and optical fiber 2m QSFP28 dedicated stack cables (supported in V200R020C10 and later versions)	100Gbit/s	2
25GE ports on the front panel	1 m, 3 m, 5 m SFP28 high-speed cables 3 m, 5 m, 7 m, and 10 m SFP28 AOC cables SFP28 optical module and fiber	25Gbit/s	4
25GE ports on the front panel	1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber (supported in V200R020C10 and later versions)	10Gbit/s	4
Ports on the S7Y08000 card	1 m, 3 m, 5 m SFP28 high-speed cables 3 m, 5 m, 7 m, and 10 m SFP28 AOC cables SFP28 optical module and fiber	25Gbit/s	8
Ports on the S7Y08000 card	1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber	10Gbit/s	8
Ports on the S7X08000 card (2 x 25GE mode)	1 m, 3 m, 5 m SFP28 high-speed cables 3 m, 5 m, 7 m, and 10 m SFP28 AOC cables SFP28 optical module and fiber	25Gbit/s	2
Ports on the S7X08000 card (2 x 25GE mode)	1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber	10Gbit/s	2
Ports on the S7X08000 card (8 x 10GE mode)	1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber 0.5 m and 1.5 m SFP+ dedicated stack cables	10Gbit/s	8

Table 3-31 S5732-H48XUM2CC Service port stacking support

Port Supporting Stacking	Stack Cable	Rate of a Single Port	Maximum of Stack Member Ports in a Logical Stack Port
MultiGE ports on the front panel	Category 6A or higher network cables (If Category 6 cables are used, ensure that the cables meet requirements of TSB-155.)	10Gbit/s	8
10GE ports on the front panel	1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber 0.5 m and 1.5 m SFP+ dedicated stack cables Only the last 16 10GE ports on the front panel can be used to set up a stack using dedicated stack cables.	10Gbit/s	8
40GE/100GE ports on the front panel	1 m, 3 m, and 5 m QSFP+ high-speed copper cables QSFP+ optical module and optical fiber (QSFP-40G-SR-BD optical modules can be used for stack since V200R019C10SPC500.) 10 m QSFP+ AOC cable	40Gbit/s	2
40GE/100GE ports on the front panel	1 m, 3 m, and 5 m QSFP28 high-speed copper cables 10 m QSFP28 AOC cables QSFP28 optical module and optical fiber 2m QSFP28 dedicated stack cables (supported in V200R020C10 and later versions)	100Gbit/s	2
25GE ports on the front panel	1 m, 3 m, 5 m SFP28 high-speed cables 3 m, 5 m, 7 m, and 10 m SFP28 AOC cables SFP28 optical module and fiber	25Gbit/s	4
25GE ports on the front panel	1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber (supported in V200R020C10 and later versions)	10Gbit/s	4
Ports on the S7Y08000 card	1 m, 3 m, 5 m SFP28 high-speed cables 3 m, 5 m, 7 m, and 10 m SFP28 AOC cables SFP28 optical module and fiber	25Gbit/s	8
Ports on the S7Y08000 card	1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber	10Gbit/s	8
Ports on the S7X08000 card (2 x 25GE mode)	1 m, 3 m, 5 m SFP28 high-speed cables 3 m, 5 m, 7 m, and 10 m SFP28 AOC cables SFP28 optical module and fiber	25Gbit/s	2
Ports on the S7X08000 card (2 x 25GE mode)	1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber	10Gbit/s	2
Ports on the S7X08000 card (8 x 10GE mode)	1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 10GE SFP+ optical module and optical fiber	10Gbit/s	8

Translation

Favorite

Download

Update Date：2023-03-02

Document ID：EDOC1100197309

Downloads：708

Average rating：2.0Points

Digital Signature File

digtal sigature tool

S300, S500, S2700, S5700, and S6700 V200R020C10 Configuration Guide - Device Management

S5732-H Service Port Stacking Support

Related Documents

Digital Signature File

Share