WLAN Hardware Installation and Maintenance Guide
AirEngine 5573-23HW (50087253)
Overview
| Item | Details |
|---|---|
| Description | AirEngine5573-23HW(11be indoor,2+2 dual bands,smart antenna,USB,BLE,1*2.5G/GE port with a BIDI LC connector) |
| Part Number | 50087253 |
| Model | AirEngine 5573-23HW |
| First supported version | V600R023C10 |
Appearance
Ports
1 |
DC 12V |
2 |
PoE_IN |
3 |
2.5G/GE |
4 |
USB |
5 |
GE0 to GE3 |
- |
- |
| Port | Connector Type | Description | Available Components |
|---|---|---|---|
| 2.5G/GE | LC | Optical port used for uplink Ethernet communication, supporting 2.5 Gbit/s and 1 Gbit/s. The AP has a built-in BIDI optical module, which connects to an optical fiber through the LC port. The wavelength on the AP side is TX 1310 nm/RX 1490 nm, with the transmit optical power of -9 dBm to -3 dBm and the receive optical power of -15 dBm to -3 dBm. The peer end must use an optical module with the wavelength of TX 1490 nm/RX 1310 nm and the matching power. It is recommended that the optical fiber routing distance be within 2 km. |
LC optical fiber |
| GE0 to GE3 | RJ45 | Ethernet electrical port that supports 10M/100M/1000M auto-sensing and connects to the wired Ethernet. | Network cable |
| PoE_IN | Phoenix terminal block | Supplies power to the device over the DC power cable in a hybrid cable when a PSE supplies power to the AP through this port. | Phoenix terminal block |
| DC 12V | DC connector | Connects to a 12 V power adapter. | 12 V DC power adapter |
| USB | USB 3.0 Type A | Connects to an IoT terminal to implement IoT applications. (USB 2.0 is supported in V600R024C10 and later versions. USB 3.0 is unavailable and will be supported through software upgrade in the future.) |
IoT module |
Indicators and Buttons
1 |
Indicator |
2 |
Default |
| Silkscreen | Name | Color | Status | Description |
|---|---|---|---|---|
| - | System indicator | - | Off | The system is not running. |
| Green | Steady on |
|
||
| Green | Steady on after blinking once | After the hardware reset is cleared and the software starts, the indicator blinks once. Then, the indicator is steady on until the system starts. | ||
| Green | Slow blinking (0.5 Hz) | The AP is running properly, the Ethernet connection is normal, and STAs are associated with the AP. | ||
| Green | Slow blinking (0.2 Hz) | The AP is running properly, the Ethernet connection is normal, and no STA is associated with the AP. | ||
| Green | Blinking once every 0.25s (4 Hz) |
|
||
| Yellow (blinking red and green at the same time, causing color deviation) | Blinking once every 0.25s (4 Hz) | Hold down the Default button for more than 6 seconds to restore the factory settings. This function is supported in V600R024C10 and later versions. |
||
| Red | Steady on | The system is faulty. |
| Silkscreen | Name | Description |
|---|---|---|
| Default | Reset button |
|
Technical Specifications
| Item | Specification |
|---|---|
| Installation Type |
|
| Dimensions without packaging (H x W x D) [mm(in.)] | 160 mm x 86 mm x 38 mm (6.30 in. x 3.39 in. x 1.50 in.) |
| Dimensions with packaging (H x W x D) [mm(in.)] | 73 mm x 203 mm x 114 mm (2.87 in. x 7.99 in. x 4.49 in.) |
| Weight without packaging [kg(lb)] | 0.39 kg (0.86 lb) |
| Weight with packaging [kg(lb)] | 0.53 kg (1.17 lb) |
| Storage | NAND Flash 256 MB |
| Console port | BLE console |
| Maximum power consumption [W] | 14.2 (excluding USB) |
| Maximum heat dissipation [BTU/hour] | 46.0 BTU/hour |
| Power supply mode |
|
| Rated input voltage [V] | 12 V |
| Input voltage range [V] | 12 V ± 10% PoE: 802.3af/at |
| Service port surge protection | PoE port: Differential mode (48 V-RTN): 0.5 kV (1.2/50 us, 42 ohms), criterion B Common mode (8 wires to ground): 4 kV (1.2/50 us, 42 ohms), criterion B |
| PoE OUT | Not supported |
| Maximum number of physical ports on the entire device | GE (RJ45) x 4, supporting 10M/100M/1000M auto-sensing 2.5G/GE (LC) optical port x 1 (The AP has a built-in BIDI optical module, which connects to an optical fiber through the LC port. The wavelength on the AP side is TX 1310 nm/RX 1490 nm, with the transmit optical power of -9 dBm to -3 dBm and the receive optical power of -15 dBm to -3 dBm. The peer end must use an optical module with the wavelength of TX 1490 nm/RX 1310 nm and the matching power. It is recommended that the optical fiber routing distance be within 2 km.) |
| Long-term operating temperature [°C(°F)] | 0°C to 40°C (32°F to 104°F) (From 1800 m to 5000 m [5905.51 ft. to 16404.20 ft.], the maximum ambient temperature decreases by 1°C [1.8°F] for every 300 m [984.25 ft.] increase in altitude.) |
| Storage temperature [°C(°F)] | –40°C to +70°C (–40°F to +158°F) |
| Long-term operating relative humidity [RH] | 5% RH to 95% RH, non-condensing |
| Long-term operating altitude [m(ft.)] | –60 m to +5000 m (–196.85 ft to +16404.20 ft) |
| Atmospheric pressure [kPa] | 53kPa - 106kPa ETSI 300 019-2-3 |
| Ground | Floating ground |
| USB | The USB port can supply 2.5 W or 5 W power. USB 2.0 is supported in V600R024C10 and later versions. USB 3.0 is unavailable and will be supported through software upgrade in the future. |
| IoT slot | Not supported |
| BLE | BLE5.2 |
| Radio number | 2 |
| Operating frequency band |
|
| MIMO spatial streams | Radio 0 (2.4 GHz): 2x2 Radio 1 (5 GHz): 2x2 |
| Wi-Fi standard | 2.4 GHz: 802.11b/g/n/ax/be 5 GHz: 802.11a/n/ac/ac Wave 2/ax/be |
| Radio interface | Built-in smart antennas |
| Antenna gain | 2.4 GHz: 3 dBi/chain (peak gain) 1 dBi (combined gain) 5 GHz: 3 dBi/chain (peak gain) 1 dBi (combined gain) BLE: 4 dBi (peak value) |
| Maximum transmit power | 2.4 GHz: 20 dBm/chain 23 dBm (combined power) 5 GHz: 20 dBm/chain 23 dBm (combined power) BLE: < 10 dBm |
| Singal radio transmit power [dBm] | 2.4G: -10 dBm to 20 dBm/chain 5G: -10 dBm to 20 dBm/chain |
| MTBF [year] | 143.611 year |
| MTTR [hour] | 2 hour |
| Frequency stability [ppm] | +/-20 |
| 802.3bt power supply description | The power supply mode is negotiated to 802.3at, and no function is restricted. |
| 802.3at power supply description | No function is limited. |
| 802.3af power supply description | The USB function is not supported. Other functions are not restricted. |
| DC power supply description | No function is limited. |