S7700 Series Switches Hardware Description
LSS7X24BX6S0 (03033DAG/03033DAG-001/03033DAG-002: 24-Port 10GE SFP+ Interface and 24-Port GE SFP Interface Card (X6S, SFP+))
Version Mapping
Card Name |
Part Number |
S7700 Chassis |
|---|---|---|
LSS7X24BX6S0 |
03033DAG |
Supported in V200R019C00 and later versions NOTE:
As for cards manufactured since June 2021: If they are used in V200R019C00, load V200R019SPH029 or a later patch, and load S7700_V200R019C00SPC500_BOARD_MOD002.mod or a later .mod file. |
03033DAG-001 |
Supported in V200R021C10SPC500 and later versions NOTE:
|
|
03033DAG-002 |
Supported in V200R021C10SPC600 and later versions NOTE:
|
Introduction
The LSS7X24BX6S0 can be installed in:
- Slots 01 to 03 in an S7703 or S7703 PoE chassis.
- Slots 01 to 06 in an S7706 or S7706 PoE chassis.
- Slots 01 to 12 in an S7712 chassis.
Functions
Function |
Description |
|---|---|
Basic functions |
Provides twenty-four 10GE optical ports and twenty-four GE optical ports for data transmission and switching. |
Distributed forwarding |
Performs concurrent data forwarding using a distributed data plane. |
Hot swapping |
The LSS7X24BX6S0 is hot swappable. |
Indicators and Ports
Number |
Indicator |
Color |
Description |
|---|---|---|---|
1 |
ACT indicator of a lower optical port |
Yellow |
Blinking: The port is transmitting and receiving data. |
2 |
ACT indicator of an upper optical port |
||
3 |
LINK indicator of a lower optical port |
Green |
Steady on: A link has been established on the port. |
4 |
LINK indicator of an upper optical port |
||
5 |
RUN/ALM: running status indicator |
Green |
Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting. |
Red |
Steady on: The card has failed and the fault requires manual intervention. |
||
Yellow |
Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.) |
1 |
Twenty-four 10GBASE SFP+/1000BASE-X ports |
2 |
Twenty-four 1000BASE-X ports |
- When a lot of cables are connected to a card, the cable management frame for this slot may not have sufficient space. In this case, deploy cables in three layers that do not cross over each other, and then put the three layers through the cable management frame. See Figure 7-268.
- It is not recommended to connect copper cables and optical fibers to the same card because copper cables may block the routes of optical fibers. If copper cables and optical fibers are used on the same card, connect the optical fibers to ports near the left side of the card and the copper cables to ports near the right side, as shown in Figure 7-269.
10GBASE SFP+/1000BASE-X port
10GBASE SFP+/1000BASE-X ports support 10GE and GE auto sensing.
Attribute |
Description |
|---|---|
Connector type |
SFP+ |
Optical port attributes |
Depend on the SFP optical module used. For the optical modules supported by the LSS7X24BX6S0 and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules. |
Standards compliance |
IEEE802.3z |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Attribute |
Description |
|---|---|
Connector type |
SFP+ |
Optical port attributes |
Depend on the SFP+ to SFP+ high-speed cable (1 m, 3 m, 5 m, 10 m), QSFP+ to 4*SFP+ high-speed cable (1 m, 3 m, 5 m), SFP+ optical module, or SFP+ optical cable used. For the optical modules supported by the LSS7X24BX6S0 and their attributes, see 10GE SFP+ Optical Modules (OSXD22N00 not supported), 10GE-CWDM SFP+ Optical Modules and 10GE-DWDM SFP+ Optical Modules. NOTE:
The S7703, S7706 and S7712 do not support SFP-10G-ZR, 10GE-CWDM SFP+ Optical Modules and 10GE-DWDM SFP+ Optical Modules. |
Standards compliance |
IEEE 802.3ae |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Attribute |
Description |
|---|---|
Connector type |
SFP+ |
Optical port attributes |
Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates). |
Applicable cable |
SFP copper module and Ethernet cable |
1000BASE-X ports
Table 7-599 lists the attributes of a 1000BASE-X port with an optical module installed.
Attribute |
Description |
|---|---|
Connector type |
SFP |
Optical port attributes |
Depend on the SFP optical module used. For details about optical modules supported by the LSS7X24BX6S0 and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules. |
Standards compliance |
IEEE 802.3z |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Table 7-600 lists the attributes of a 1000BASE-X port with a copper module installed.
Attribute |
Description |
|---|---|
Connector type |
SFP |
Optical port attributes |
Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates). |
Applicable cable |
SFP copper module and Ethernet cable |
Specifications
Item |
Description |
|---|---|
Physical specifications |
|
Ordering Information
Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.
Part Number |
Card Description |
Card Model |
|---|---|---|
|
24-Port 10GE SFP+ Interface and 24-Port GE SFP Interface Card (X6S, SFP+) |
LSS7X24BX6S0 |