S7700 Series Switches Hardware Description
ES1D2S24SX2S-24-Port 10GE SFP+ Interface and 8-Port GE SFP Interface Card (X2S, SFP+)
Version Mapping
Card Name |
S7700 Chassis |
|---|---|
ES1D2S24SX2S |
S7703, S7706, and S7712 chassis: supported in V200R010C00 and later versions S7703 PoE and S7706 PoE chassis: supported in V200R013C00 and later versions |
Introduction
The ES1D2S24SX2S can be installed in:
- Slots 01 to 03 in an S7703 or S7703 PoE chassis.
- Slots 01 to 06 in an S7706 or S7706 PoE chassis.
- Slots 01 to 12 in an S7712 chassis.
Functions
Function |
Description |
|---|---|
Basic functions |
Provides twenty-four 10GE optical ports and eight GE optical ports for data transmission and switching. |
Distributed forwarding |
Performs concurrent data forwarding using a distributed data plane. |
Hot swapping |
The ES1D2S24SX2S is hot swappable. |
Usage Constraints
The card cannot be used with the SRUHX1 series cards.
Indicators and Ports
Number |
Indicator |
Color |
Description |
|---|---|---|---|
1 |
ACT indicator of a lower optical port |
Yellow |
Blinking: The port is transmitting and receiving data. |
2 |
ACT indicator of an upper optical port |
||
3 |
LINK indicator of a lower optical port |
Green |
Steady on: A link has been established on the port. |
4 |
LINK indicator of an upper optical port |
||
5 |
RUN/ALM: running status indicator |
Green |
Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting. |
Red |
Steady on: The card has failed and the fault requires manual intervention. |
||
Yellow |
Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.) |
1 |
Twenty-four 10GBASE SFP+/1000BASE-X ports |
2 |
Eight 1000BASE-X ports |
10GBASE SFP+/1000BASE-X port
10GBASE SFP+/1000BASE-X ports support 10GE and GE auto sensing. Table 7-566 describes the attributes of a port working in 1000M mode, and Table 7-567 describes the attributes of a port working in 10G mode. Table 7-568 describes the attributes of a 10GBASE SFP+/1000BASE-X port using a copper module.
Attribute |
Description |
|---|---|
Connector type |
SFP+ |
Optical port attributes |
Depend on the SFP optical module used. For the optical modules supported by the ES1D2S24SX2S and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules. |
Standards compliance |
IEEE802.3z |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Attribute |
Description |
|---|---|
Connector type |
SFP+ |
Optical port attributes |
Depend on the SFP+ to SFP+ high-speed cable (1 m, 3 m, 5 m, 10 m), QSFP+ to 4*SFP+ high-speed cable (1 m, 3 m, 5 m), SFP+ optical module, or SFP+ optical cable used. For the optical modules supported by the ES1D2S24SX2S and their attributes, see 10GE SFP+ Optical Modules (OSXD22N00 not supported), 10GE-CWDM SFP+ Optical Modules and 10GE-DWDM SFP+ Optical Modules. |
Standards compliance |
IEEE 802.3ae |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Attribute |
Description |
|---|---|
Connector type |
SFP+ |
Optical port attributes |
Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates). |
Applicable cable |
SFP copper module and Ethernet cable |
1000BASE-X ports
Table 7-569 lists the attributes of a 1000BASE-X port with an optical module installed.
Attribute |
Description |
|---|---|
Connector type |
SFP |
Optical port attributes |
Depend on the SFP optical module used. For details about optical modules supported by the ES1D2S24SX2S and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules. |
Standards compliance |
IEEE 802.3z |
Frame format |
Ethernet_II, Ethernet_SAP, Ethernet_SNAP |
Network protocol |
IP |
Table 7-570 lists the attributes of a 1000BASE-X port with a copper module installed.
Attribute |
Description |
|---|---|
Connector type |
SFP |
Optical port attributes |
Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates). |
Applicable cable |
SFP copper module and Ethernet cable |
Specifications
Item |
Description |
|---|---|
Physical specifications |
|
Ordering Information
Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.
Part Number |
Card Description |
Card Model |
|---|---|---|
03031YFH |
24-Port 10GE SFP+ Interface and 8-Port GE SFP Interface Card (X2S, SFP+) |
ES1D2S24SX2S |