HUAWEI USG6000 Series V100, V500 Hardware Guide

USG6550, USG6570

The USG6550, USG6570 has only AC models and no DC models and uses an integrated chassis that contains the fixed interface board, single power module, and built-in fan module. You can also add some optional modules, such as hard disk, additional power module, and expansion cards, to improve system reliability and add more ports.

Mapping

Table 2-50 lists the mapping between the USG6550, USG6570 hardware and software versions.

Table 2-50 Mapping between the hardware and software versions

Model	Software Version
USG6550, USG6570	V100R001C10, V500R001C00, and later versions

Front Panel

Figure 2-36 illustrates the front panel of the USG6550, USG6570.

Figure 2-36 USG6550, USG6570 front panel

Name	Description
Slot numbering	Identifies the slot type and number, with 0 indicating the slot for the out-of-band MGMT port (GigabitEthernet 0/0/0), 1 the slot for the interface board, and 2 and 3 the WSIC slots. Interfaces are numbered in the format of "interface type A/B/C", where: A is the slot number of the interface card. B is the daughter card number, which is 0 because no daughter card is installed now. C is the interface number, which begins with 0 and is numbered from bottom to top and left to right.
Fixed interface board	The core component for system control and management. The interface board provides an out-of-band management port, console port, and USB port for management access. The interface board is built-in and cannot be removed.
Expansion slot	Provides two Wide Service Interface Card (WSIC) slots for expansion cards. Table 2-28 lists the supported expansion cards.
ESD jack	The equipment end of the wrist strap is inserted into the ESD jack. For the wrist strap to be effective, ensure that the device is already grounded.

The expansion slots on the USG6550, USG6570 support the expansion cards listed in Table 2-51.

Table 2-51 Supported expansion cards

Expansion Card	Description
8GE WSIC Interface Card	Provides eight gigabit RJ45 Ethernet ports.
2XG8GE WSIC Interface Card	Provides eight gigabit RJ45 ports and two 10-gigabit SFP+ ports.
8GEF WSIC Interface Card	Provides eight gigabit SFP ports.
4GE-BYPASS WSIC Card	Provides two electrical bypass links.

Fixed Interface Board

Figure 2-37 illustrates the fixed interface board panel of the USG6550, USG6570.

Figure 2-37 Fixed interface board panel of the USG6550, USG6570

Table 2-52 Interface description

Name	Description
MGMT port	Out-of-band 10/100/1000M RJ45 autosensing Ethernet management port. The interface number is GigabitEthernet 0/0/0 and the default IP address of the interface is 192.168.0.1. You can connect this port to the network port or any reachable port on a PC through a network cable. Then, you can use Telnet to access the CLI or use a web browser to access the web UI to configure, manage, and maintain the USG. NOTE: The MGMT port cannot be used as a service port.
Console port (RJ45)	Console ports allow you to locally connect a PC to the device. You can use a console cable to connect the console port (RJ45) on the device to the COM port on your PC and use a serial port terminal program on your PC to access, configure, and manage the device.
USB0 and USB1 ports	USB ports allow you to insert USB devices for system software upgrades. For details on upgrades through USB devices, refer to the Upgrade Guide delivered with the device. USB ports allow you to insert 4G LTE data cards. For details on the 4G LTE data cards, refer to 4G LTE Data Card.
0 to 7 (RJ45) NOTE: Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top.	Service ports. They are eight 10/100/1000M autosensing Ethernet electrical ports numbered from GigabitEthernet 1/0/0 to GigabitEthernet 1/0/7.
8 to 11 (SFP) NOTE: Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top.	Service ports. They are four GE optical ports numbered from GigabitEthernet 1/0/8 to GigabitEthernet 1/0/11. Each port requires a 1 Gbit/s SFP Electrical Module or a 1 Gbit/s eSFP Optical Module.
RST button	To restart the device, press the RST button. Ensure that the running configuration is saved before pressing the RST button. The RST button can also be used to restore the default settings. To do so, press and hold down the RST button and power on the device. When the MODE indicator of the fixed interface board blinks (about 3 to 5 seconds later), release the button. The device then starts with the default configuration. NOTE: If the device has a hard disk installed, before pressing the RST button to reset, run the disk offline command in the user view. Wait about 30 seconds until the system indicates that the hard disk stops working and then press the RST button. Otherwise, the data may be lost or hard disk be damaged.

Table 2-53 Indicator description

Indicator	Name	Color	Status	Description
SYS	System indicator	Green	Steady on	The system is being powered on or restarted.
		Green	Blink every two seconds (0.5 Hz)	The system is running normally.
		Green	Blink twice every second (2 Hz)	The system is starting.
		Green	Blink eight times every second (8 Hz)	The system software or configuration file is being upgraded.
		-	Off	The system is faulty.
ALM NOTE: If the system starts with dual power modules but one power module is not powered on, the ALM indicator is steady red, but the system is operating properly.	ALM indicator	Red	Steady on	The system is faulty. For example, the power-on self test (POST), power voltage, or temperature is abnormal.
	ALM indicator	-	Off	The system is running normally.
PWR	Power indicator	Green	Steady on	The power module works properly.
PWR	Power indicator	-	Off	The power module is faulty or the power cable is disconnected.
HDD	HDD indicator	Green	Steady on	The hard disk is running.
		Green	Blink	Data is being read from or written to the hard disk.
		-	Off	The hard disk is not detected.
MODE	MODE indicator	Green	Steady on	Hot standby is not configured, or hot standby is configured but the device is the standby device in an active/standby mode or the hot standby mode is load balancing.
MODE	MODE indicator	-	Off	Hot standby is configured in active/standby mode and the device is the standby device.
MGMT	MGMT indicator	Green	Steady on	The link is connected.
		Green	Blink eight times every second (8 Hz)	Data is being sent or received.
		-	Off	The link is disconnected or not properly connected.
-	LINK indicator	Green	Steady on	The link is connected.
-	LINK indicator	-	Off	The link is disconnected.
-	ACT indicator	Yellow	Steady on	Data is being sent or received.
-	ACT indicator	-	Off	No data is being sent or received.
-	Indicator for optical ports 8 to 11	Green	Steady on	The link of the port is connected.
		Green	Blink	Data is being sent or received through the port.
		-	Off	The link of the port is disconnected.

Rear Panel

Figure 2-38 illustrates the rear panel of the USG6550, USG6570.

Figure 2-38 USG6550, USG6570 rear panel

Name	Description
Slot numbering	Indicates the layout of the slots, including the slot number and module type.
Power modules (in slots PWR5 and PWR6)	Provides power input and distribution for the device. One power module is provided by default, but two power modules are supported to provide 1+1 power redundancy. If two power modules are used and one power module fails, the other can support the entire system so that you can replace the faulty power module without interrupting device operation. For details, see 170 W AC Power Module.
Hard disk combination (in slot HDD4)	The device supports optional hard disk combination SM-HDD-SAS300G-B, SM-HDD-SAS600G-B or SM-HDD-SAS1200G-B. Hard disks are used to store logs and reports, and they can be purchased from Huawei if necessary. For details, see Hard Disk Combination SM-HDD-SAS300G-B, Hard Disk Combination SM-HDD-SAS600G-B, and Hard Disk Combination SM-HDD-SAS1200G-B. If no hard disk is installed, a filler panel must be installed on slot HDD4 to ensure normal air flow and keep out dust. NOTICE: The USG starts to support SM-HDD-SAS600G-B hard disk combination since V500R001C30SPC100. If you use SM-HDD-SAS600G-B hard disk combination on earlier versions, the SM-HDD-SAS600G-B hard disk combination will be identified as non-Huawei hard disks. You need to upgrade the software version. The USG starts to support SM-HDD-SAS1200G-B hard disk combination since V500R001C50. If you use SM-HDD-SAS1200G-B hard disk combination on earlier versions, the SM-HDD-SAS1200G-B hard disk combination will be identified as non-Huawei hard disks. You need to upgrade the software version.
SN	The serial number that uniquely identifies the device. The SN of the device must be provided to the local technical support personnel of Huawei to apply for a license.
Protective ground terminal	The M4 OT terminal of the ground cable is connected to the protective ground terminal of the device, and the other terminal of the ground cable is connected to the ground point of the cabinet or workbench or the ground bar of the equipment room.

Power Supply System

By default, the USG6550, USG6570 has a 170 W AC power module, but two power modules are supported for 1+1 power redundancy.

Heat Dissipation System

The USG adopts the automatic fan speed adjustment technology to monitor the temperature of key components. If the internal device temperature is higher than the specified value, the fan speed increases; when the temperature falls back to its normal range, the fan speed decreases. In this way, the fan module enables the device to run in normal temperature, ensuring device running security and reliability.

Figure 2-39 illustrates the air flow of the device. The air intake areas include the left side and the hard disk installation slot on the front side, and the air exhaust is on the right side. The built-in fan module locates at the air exhaust and cannot be removed.

Figure 2-39 System Air Flow

Technical Specifications

Table 2-54 lists the technical specifications of the USG6550, USG6570.

Table 2-54 USG6550, USG6570 technical specifications

Item		Description
Part number		USG6550-AC: 02358671 USG6550-BDL-AC: 02358672 USG6570-AC: 02358673 USG6570-BDL-AC: 02358674
System specifications
CPU		Multi-core 1.1 GHz processor
Memory		DDR3 4GB
Flash		16MB
CF card		2 GB
Hard disk		Optional hot-swappable 300GB, 600GB or 1200GB 2.5-inch SAS hard disk. The hard disk unit is hot-swappable, but the hard disk combination is not hot-swappable.
SPUB (the service engine)		Not supported
4G LTE data card		Supported
Dimensions and weight
Dimensions (H^a x W^b x D)		44.4 mm x 442 mm x 421 mm (1.75 in. x 17.4 in. x 16.57 in., 1 U)
Weight		Standard: 6 kg Fully configured: 8.6 kg
Power consumption and heat consumption
Typical power consumption		73.2 W
Maximum power consumption		74.1 W
Typical heat consumption		249.8 BTU/hour
Maximum heat consumption		252.8 BTU/hour
Power specifications
AC model		Supported. By default, one power module is provided. If two power modules are used and one module fails, you can hot-swap the faulty power module.
Rated input voltage (AC)		100 V to 240 V, 50 Hz/60 Hz
Maximum input voltage (AC)		90 V to 264 V, 47 Hz to 63 Hz
Maximum input current (AC)		2.5 A
Maximum output power (AC)		170 W
DC model		Not supported
Heat dissipation
Fan module		Built-in fan module, cannot be removed.
Number of fans		5
Air flow (hot air flow, viewed facing the rear panel)		Intake on the front and left sides, exhaust on the right side
Port density
Out-of-band management port		1 (RJ45)
Console port		1 (RJ45)
USB 2.0 port		2
Service ports in standard configuration		4 GE optical ports 8 10/100/1000M autosensing Ethernet electrical ports
Expansion slot		2×WSIC
Types of expansion cards		8GE-WSIC-8×1GE RJ45 interface card 2XG8GE-WSIC-8×1GE RJ45+2×10GE SFP+ interface card 8GEF-WSIC-8×1GE SFP interface card 4GE-BYPASS-WSIC-2×electrical links Bypass card
Environment specifications^c
System reliability	MTBF (year)	11.96
System reliability	MTTR (hour)	1
Ambient temperature	Short-term^d	Without hard disk: -5°C to 55°C With hard disk(s)^e: 5°C to 40°C
Ambient temperature	Long-term	Without hard disk: 0°C to 45°C With hard disk(s)^e: 5°C to 40°C
Storage ambient temperature		-40°C to 70°C
Operating ambient relative humidity		Without hard disk: 5% RH to 95% RH, non-condensing With hard disk(s): 5% RH to 90% RH, non-condensing
Storage ambient relative humidity		Without hard disk: 5% RH to 95% RH, non-condensing With hard disk(s): 5% RH to 90% RH, non-condensing
Altitude		Without hard disk: 5,000 m With hard disk(s): 3,000 m
NOTE: a. The height is 1 U (1 U = 1.75 inches, or about 44.45 mm), which is a height unit defined in International Electrotechnical Commission (IEC) 60297 standards. b. The width does not include the size of mounting ears. c. Temperature and humidity are measured 1.5 m above the floor and 0.4 m in front of the rack when no protection plate exists before or after the rack. d. The short term operating conditions mean that the continuous operating period does not exceed 48 hours and the accumulative total period within a year does not exceed 15 days. If the continuous operating period exceeds 48 hours or the total period within a year exceeds 15 days, it is regarded as long term. e. The ambient temperature change rate of a device with hard disk(s) is less than or equal to 20°C per hour.

Mapping
Front Panel
Fixed Interface Board
Rear Panel
Power Supply System
Heat Dissipation System
Technical Specifications

Translation

Favorite

Download

Update Date：2020-12-03

Document ID：EDOC1100023967

Downloads：2924

Average rating：0.0Points