NetEngine AR600, AR6100, AR6200, and AR6300 Web-based Typical Configuration Examples

Example for Configuring Internet Access Through PPPoE Dial-Up (LAN Interfaces in Different VLANs)

Specifications

This example applies to all AR models of V300R019C10 and later versions.

Networking Requirements

In Figure 2-44, the router functions as a PPPoE client and obtains an IP address (user name user1 and password YsHsjx_202206) after being authenticated by the PPPoE server to provide Internet access to intranet users. LAN interfaces are connected to the intranet, and the IP address of the DNS server is 172.16.0.0/24. VLAN planning in this example is as follows: The network segments of VLANs 100 and 200 are 192.168.2.0/24 and 192.168.1.0/24 respectively.

Figure 2-44 Configuring Internet access through PPPoE dial-up

Procedure

WAN-side configuration
1. Choose Configuration > WAN Configuration > Ethernet Interface. The Ethernet Interface Setting page is displayed, as shown in Figure 2-45.
  
  Figure 2-45 Ethernet Interface Setting page
2. In the Operation column of the Ethernet Interface List, click Modify corresponding to GigabitEthernet0/0/1 to be configured. The Ethernet Interface Setting dialog box is displayed, as shown in Figure 2-46. Set the parameters according to the following figure.
  Figure 2-46 Ethernet Interface Setting (when the connection mode is set to PPPoE)
3. Click OK to finish configuring the WAN interface.
LAN-side configuration
- Configuring VLAN 100
  1. Choose Configuration > LAN Configuration > VLAN. The VLAN Settings page is displayed, as shown in Figure 2-47.
    
    Figure 2-47 VLAN Settings page
  2. In the VLAN Settings, perform the following steps to configure VLAN 100 and its interfaces.
    1. Select or enter parameters according to Figure 2-48.
      Figure 2-48 Creating a VLAN interface
    2. Click Configuration in the Select interface, as shown in Figure6. Select an interface from the Available Interface list, and click . In the Modify Link Type dialog box, set Link Type to Access, as shown in Figure7. Click OK. The selected interface will be moved to the Added Interface List.
      Figure 2-49 Select interface
      
      Figure 2-50 Modify Link Type
    3. In the VLAN Settings dialog box, click Add to finish creating and configuring VLAN 100.
  3. In the VLANIF Settings, perform the following steps to configure VLAN 100 and its interfaces.
    1. Perform the following steps to configure VLAN 100 and its interfaces, as shown in Figure8.
      Figure 2-51 VLANIF Settings
    2. Click Add to finish configuring VLAN 100.
- Configuring VLAN 200
  1. Choose Configuration > LAN Configuration > VLAN. The VLAN Settings page is displayed, as shown in Figure9.
    
    Figure 2-52 VLAN Settings page
  2. In the VLAN Settings, perform the following steps to configure VLAN 200 and its interfaces.
    1. Select or enter parameters according to Figure10.
      Figure 2-53 Creating a VLAN interface
    2. Click Configuration in the Select interface, as shown in Figure11. Select an interface from the Available Interface list, and click . In the Modify Link Type dialog box, set Link Type to Access, as shown in Figure12. Click OK. The selected interface will be moved to the Added Interface List.
      Figure 2-54 Select interface
      
      Figure 2-55 Modify Link Type
    3. In the VLAN Settings dialog box, click Add to finish creating and configuring VLAN 200.
  3. In the VLANIF Settings, perform the following steps to configure VLAN 200 and its interfaces.
    1. Perform the following steps to configure VLAN 200 and its interfaces, as shown in Figure13.
      Figure 2-56 VLANIF Settings
    2. Click Add to finish configuring VLAN 200.
After the preceding configurations are complete, intranet users can access the Internet through the router.