SupportDocumentationSwitchesCampus SwitchS3700&S5700&S6700Learn About ProductsHardware Description

S5700 Series Switches Hardware Description (V200)

S5731-S24P4X (02353AHX/02353AHX-001/02353AHX-003)

S5731-S24P4X (02353AHX/02353AHX-001/02353AHX-003)

Version Mapping

Table 4-1223 lists the mapping between the S5731-S24P4X chassis and software versions.

Table 4-1223 Version mapping

Series

Model

Software Version

S5731-S

S5731-S24P4X

02353AHX: V200R019C00 and later versions

02353AHX-001: V200R020C10 and later versions

02353AHX-003: V200R021C10SPC600 and later versions (If V200R021C10SPC500 is used, install V200R021HP0121 or a later patch.)

Appearance and Structure

Figure 4-484 S5731-S24P4X (02353AHX) appearance
Figure 4-485 S5731-S24P4X (02353AHX-001/02353AHX-003) appearance

1

Twenty-four PoE+ 10/100/1000BASE-T ports

2

Four 10GE SFP+ ports

Applicable modules and cables:

3

One console port

4

One ETH management port

5

One USB port

6

One PNP button

NOTICE:

To restore the factory settings and reset the switch, hold down the button for at least 6 seconds.

To reset the switch, press the button.

Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.

7

Ground screw

NOTE:
It is used with a ground cable.

8

Fan module slot 1

NOTE:

Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust))

9

Fan module slot 2

NOTE:

Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust))

10

Power module slot 1

NOTE:

Applicable power module:

11

Power module slot 2

NOTE:

Applicable power module:

-

-

Port Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 4-1224 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.
Table 4-1224 Attributes of a 10/100/1000BASE-T Ethernet electrical port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3, IEEE802.3u, IEEE802.3ab

Working mode

10/100/1000 Mbit/s auto-sensing

Maximum transmission distance

100 m

10GE SFP+ optical port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-1225 describes the attributes of a 10GE SFP+ Ethernet optical port.
Table 4-1225 Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-1226.
Table 4-1226 Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-1227 describes the attributes of an ETH management port.
Table 4-1227 Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working Mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m
In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the Configuration Guide - Basic Configuration. If you have logged in to the switch for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5731-S24P4X has the same types of indicators as the S5731-S48P4X. For details, see Indicator Description.

Power Supply Configuration

The switch is a PoE switch and supports two power module slots, each of which can have a 1000 W PoE or 600 W PoE power module installed. Pluggable AC and DC PoE power modules can be used together in the same switch.

Table 4-1228 Power supply configurations

Power Module 1

Power Module 2

Available PoE Power

Maximum Number of Ports (Fully Loaded)

1000 W AC (220 V)

1000 W DC

–

760 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 24

1000 W AC (110 V)

–

665 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 22

1000 W AC (220 V)

1000 W DC

1000 W AC (220 V)

1000 W DC

1600 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 24

1000 W AC (110 V)

1000 W DC

1000 W AC (110 V)

Versions earlier than V200R021C10: 1330 W

V200R021C10 and later versions: 1520 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 24

600 W AC (220 V)

–

380 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 12

600 W AC (110 V)

–

95 W
  • 802.3af (15.4 W per port): 6
  • 802.3at (30 W per port): 3

600 W AC (220 V)

600 W AC (220 V)

950 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 24

600 W AC (110 V)

600 W AC (110 V)

380 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 12

1000 W AC (220 V)

1000 W DC

600 W AC (220 V)

1330 W
  • 802.3af (15.4 W per port): 24
  • 802.3at (30 W per port): 24

When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.

Heat Dissipation

The S5731-S24P4X uses pluggable fan modules for forced air cooling. Air flows in from the front side and exhausts from the rear panel.

Technical Specifications

Table 4-1229 lists technical specifications of the S5731-S24P4X.

Table 4-1229 Technical specifications

Item

Description

Memory (RAM)

2 GB

Flash

1 GB in total. To view the available flash memory size, run the display version command.

Mean time between failures (MTBF)

57.21 years

Mean time to repair (MTTR)

2 hours

Availability

> 0.99999

Service port surge protection

Common mode: ±6 kV

Power supply surge protection
  • Using AC power modules: ±6 kV in differential mode, ±6 kV in common mode
  • Using DC power modules: ±2 kV in differential mode, ±4 kV in common mode

Dimensions (H x W x D)
  • Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.)
  • Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 448.0 mm (1.72 in. x 17.4 in. x 17.7 in.)

Weight (with packaging)

8.6 kg (18.96 lb)

Stack ports

10GE SFP+ ports on the front panel

RTC

Supported

RPS

Not supported

PoE

Supported

Rated voltage range
  • AC input: 100 V AC to 130 V AC, 200 V AC to 240 V AC, 50/60 Hz
  • High-Voltage DC input: 240 V DC
  • DC input: -48 V DC to -60 V DC

Maximum voltage range
  • AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz
  • High-Voltage DC input: 190 V DC to 290 V DC
  • DC input: -38.4 V DC to -72 V DC

Maximum power consumption (100% throughput, full speed of fans)
  • Not providing the PoE function: 121 W
  • 100% PoE loads: 977 W (PoE: 720 W)

Typical power consumption (30% of traffic load, tested according to ATIS standard)

95 W

Operating temperature
-5°C to +45°C (23°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.)
NOTE:

When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

The switch cannot be started when the ambient temperature is lower than 0°C (32°F).

Storage temperature

-40°C to +70°C (-40°F to +158°F)

Noise under normal temperature (27°C, sound power)

< 62.3 dB(A)

Relative humidity

5% to 95%, noncondensing

Operating altitude

0-5000 m (0-16404 ft.)

Certification
  • EMC certification
  • Safety certification
  • Manufacturing certification

Part number

02353AHX

02353AHX-001

02353AHX-003
Translation
Favorite
Download
Update Date：2024-04-09
Document ID：EDOC1000013597
Views：5699694
Downloads：49655
Average rating：3.27Points

Related Documents

Digital Signature File

digtal sigature tool