SupportDocumentationRoutersAccess RoutersAR600&6100&6200&6300Learn About ProductsHardware Description

NetEngine AR600, AR6100, AR6200, and AR6300 Hardware Description

AR611-LTE4EA

AR611-LTE4EA

Overview

Table 3-20 Basic information about the AR611-LTE4EA
Item Details
Description AR611-LTE4EA, 1*GE COMBO WAN, 4*GE LAN, 1*USB 2.0, 1*LTE
Part Number 50010702
Model AR611-LTE4EA
First supported version V300R022C00
Remarks Available in V300R022C00 and later versions

Appearance

Figure 3-13 Appearance of the AR611-LTE4EA

Components

Figure 3-14 Components of the AR611-LTE4EA

1. Power jack

2. RESET button

NOTE:
This button is used to reset the router.
  • To restore the factory settings, hold down the button for at least 5 seconds.
  • To reset the router, hold down the button for less than 5 seconds.
Resetting the router will interrupt services. Exercise caution when deciding to press this button.

If needed, you can run the factory-configuration prohibit command in the system view to disable the function of restoring the factory settings by holding down the RESET button. To enable this function again, run the undo factory-configuration prohibit command.

3. USB interface 2.0 (host)

4. Console interface

5. LAN interfaces: four GE electrical interfaces

6. WAN interface: GE combo interface

7. Two LTE antennas

8. Two SIM card slots

   

Slot Layout

Table 3-21 Slots on the AR611-LTE4EA
Slot Type Slot ID Slot Direction Remarks
SIM card slot SIM1 -

Two SIM card slots are supported.

  • The SIM card cover is used to protect the SIM card. Remove the SIM card cover before installing the SIM card.
  • The double-card single-standby is supported, and SIM1 is the default master card. If only one SIM card needs to be installed, install it in slot SIM1.
  • The Micro SIM card is supported. It is not recommended to use the card cover to prevent poor SIM card contact.
  • Hot-swap SIM card is not supported. After replugging the SIM card, you need to restart the RF module or restart the device.
SIM card slot SIM2 -

Two SIM card slots are supported.

  • The SIM card cover is used to protect the SIM card. Remove the SIM card cover before installing the SIM card.
  • The double-card single-standby is supported, and SIM1 is the default master card. If only one SIM card needs to be installed, install it in slot SIM1.
  • The Micro SIM card is supported. It is not recommended to use the card cover to prevent poor SIM card contact.
  • Hot-swap SIM card is not supported. After replugging the SIM card, you need to restart the RF module or restart the device.

Ports

Table 3-22 Ports on the AR611-LTE4EA
Port Connector Type Description Available Components
Console interface RJ45

The console interface can connect to an operation terminal for onsite configuration.

  • Standards compliance: RS232
  • Working mode: duplex Universal Asynchronous Receiver/Transmitter (UART)
  • Data equipment type: Data Circuit-terminating Equipment (DCE)

Console cable
LAN interfaces: four GE electrical interfaces RJ45

A GE electrical interface (10/100/1000 Mbit/s auto-sensing) transmits and receives services at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s.

  • Standards compliance: IEEE802.3, IEEE802.3u, and IEEE802.3ab
  • Working mode: full-duplex (10/100/1000 Mbit/s auto-sensing)
  • Maximum distance: 100 m
NOTE:

GE0 is a management interface and is used for web-based management and email-based deployment.

All LAN-side GE interfaces can be configured as WAN-side interfaces.

Ethernet cable
WAN interfaces: GE combo interfaces

GE electrical interface: RJ45

GE optical interface: LC/PC

A GE combo interface consists of an optical Ethernet interface and an electrical Ethernet interface on the panel. The two interfaces have only one internal forwarding interface. The electrical and optical interfaces are multiplexed, and only either of them can work at a time. When either of the Ethernet interfaces is working, the other interface is shut down.

  • The GE electrical interface (10/100/1000 Mbit/s auto-sensing) transmits and receives services at 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s.
  • The GE optical interface (100/1000 Mbit/s auto-sensing) transmits and receives services at 100 Mbit/s or 1000 Mbit/s.
NOTE:

By default, a combo interface works in auto mode and automatically works as an optical or electrical interface.
  • GE electrical interface: Ethernet cable
  • GE optical interface: optical fiber and optical module

The following optical modules are supported:

FE SFP&eSFP optical modules

GE eSFP optical modules

GPON&EPON optical modules (supported in V300R023C00 and later versions)
2 LTE antenna interfaces SMA-K (screw threads outside and a hole inside)

LTE antenna interfaces include a primary antenna interface (MAIN) and a secondary antenna interface (DIV). The primary and secondary LTE antenna interfaces work at the same time. The primary interface transmits and receives LTE signals, and the secondary interface only receives LTE signals. They work together to improve the downlink rate.

Interface standards and supported frequency bands:

EC200A-EH:

  • LTE FDD: Band 1/3/5/7/8/20/28
  • LTE TDD: Band 38/40/41
  • WCDMA: Band 1/5/8
  • GSM: 900/1800 (MHz)

Supported rates:

  • LTE FDD: 40 Mbit/s uplink and 120 Mbit/s downlink
  • LTE TDD: 30 Mbit/s uplink and 130 Mbit/s downlink
  • DC-HSPA+: 5.76 Mbit/s uplink and 42 Mbit/s downlink
  • HSPA+: 5.76 Mbit/s uplink and 21.6 Mbit/s downlink
  • WCDMA PS: 384 kbit/s uplink and 384 kbit/s downlink
  • WCDMA CS: 64 kbit/s uplink and 64 kbit/s downlink
  • EDGE: 236.8 kbit/s uplink and 236.8 kbit/s downlink
  • GPRS: 85.6 kbit/s uplink and 85.6 kbit/s downlink
  • GSM: 9.6 kbit/s uplink and 14.4 kbit/s downlink
NOTE:

An LTE whip antenna is delivered with the installation accessory package.

An LTE antenna interface can be configured with an LTE indoor remote antenna.

Whip antenna (delivered with the device by default)

LTE indoor remote antenna (27012152)
USB interface 2.0 (host) USB 2.0 Type A

A USB interface provides up to 480 Mbit/s upload and download rates.

  • Standards compliance: USB 2.0
  • Working mode: Host
NOTE:

This interface can be used only for USB-based deployment.

USB 2.0-compliant USB flash drive

Indicators and Buttons

Figure 3-15 Indicators and buttons on the AR611-LTE4EA

1. PWR indicator

2. SYS indicator

3. USB indicator

4. iNET indicator

5. CTRL indicator

6. LAN (GE0 to GE3) interface indicators

7. WWAN indicator

8. RSSI indicator

9. RSSI indicator
Table 3-23 Indicators on the AR611-LTE4EA
Silkscreen Name Color Status Description
PWR PWR indicator Green Steady on The system power supply is normal.
- Off The system power is off.
SYS SYS indicator Green Slow blinking The system is running properly.
Green Fast blinking The system is being powered on or restarting.
Red Steady on A fault that affects services has occurred. The fault cannot be rectified automatically and requires manual intervention.
- Off The system software is not running or is being reset.
USB USB indicator Green Steady on The system has been upgraded or configured using a USB flash drive.
Green Blinking The system is being upgraded or configured using a USB flash drive.
Red Steady on The system fails to be upgraded or configured using a USB flash drive.
- Off No USB flash drive is connected, the USB interface has failed, or the indicator has failed.
iNET iNET indicator Green Steady on The network service has been established.
- Off The network service is unavailable.
CTRL CTRL indicator Green Steady on The device has been connected to the controller.
- Off The device is not connected to the controller.
WWAN WWAN indicator Green Steady on A 4G/3G/2G connection has been established or is active.
Green Blinking Data is being transmitted or received over the 4G/3G/2G connection.
- Off The 4G/3G/2G connection has not been established or is inactive.
RSSI RSSI indicator Green Steady on The 4G/3G/2G signal strength is high.
Green Fast blinking The 4G/3G/2G signal strength is medium.
Green Slow blinking The 4G/3G/2G signal strength is low.
- Off No 4G/3G/2G signal is available.
GE4 GE combo interface indicator (GE4) Green Steady on A link has been established on the corresponding GE combo interface.
Green Blinking Data is being transmitted or received on the corresponding GE combo interface.
- Off No link is established on the corresponding GE combo interface.
GE0 to GE3 LAN interface indicator (GE0 to GE3) Green Steady on A link has been established on the corresponding LAN interface.
Green Blinking Data is being transmitted or received on the corresponding LAN interface.
- Off No link is established on the corresponding LAN interface.
Table 3-24 Buttons on the AR611-LTE4EA
Silkscreen Name Description
RESET Reset button

This button is used to reset the device.

  • To restore the factory settings, hold down the button for at least 5 seconds.
  • To reset the device, hold down the button for less than 5 seconds.

Resetting the device will cause service interruption. Exercise caution when you press the Reset button.

Technical Specifications

Table 3-25 Technical specifications of the AR611-LTE4EA
Item Specification
Installation type
  • Work bench
  • Against the wall
Chassis height [U] 1 U
Dimensions without packaging (H x W x D) [mm(in.)]
  • Basic dimensions: 38.0 mm x 240.0 mm x 161.5 mm (1.5 in. x 9.45 in. x 6.36 in.)
  • Maximum dimensions: 41.4 mm x 278.6 mm x 161.5 mm (1.63 in. x 10.97 in. x 6.36 in.)
Dimensions with packaging (H x W x D) [mm(in.)] 90 mm x 370 mm x 297 mm (3.54 in. x 14.57 in. x 11.69 in.)
Weight with packaging [kg(lb)] 1.31 kg (2.89 lb)
Weight without packaging [kg(lb)] 0.85 kg (1.87 lb)
CPU 1.1 GHz, 2 Cores
Memory 1 GB
NAND Flash 1 GB
Console port RJ45
RTC Supported
LAN ports 4 x GE electrical interfaces
WAN ports 1 x GE combo
Number of service board slots 0
MIC slots (default/maximum) 0/0
SIC slots (default/maximum) 0/0
WSIC slots (default/maximum) 0/0
XSIC slots (default/maximum) 0/0
Redundant MPUs Not supported
RPS input Not supported
PoE Not supported
IP rating IP20
MTBF [years] 51.63 years
MTTR [hours] 2 hours
Availability 0.9999955776
Typical power consumption [W] 14 W
Maximum power consumption [W] 17 W
Power supply mode AC power adapter
Number of power modules 1
Rated input voltage [V] 110 V to 220 V, 50 Hz/60 Hz
Input voltage range [V] 90 V to 270 V, 45 Hz to 65 Hz
Maximum input current [A] 0.8 A
Maximum output power [W] 24 W
Redundant power supply Not supported
Types of fans None
Number of fan modules 0
Heat dissipation mode Natural heat dissipation
Airflow Natural heat dissipation
Noise at normal temperature (acoustic power) [dB(A)] 0 (Natural heat dissipation)
Long-term operating temperature [°C(°F)]

0°C to 40°C (32°F to 104°F)

NOTE:

When the altitude is 1800 m-5000 m (5906 ft.-16404.2 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
Long-term operating relative humidity [RH] 5% RH to 95% RH, non-condensing
Long-term operating altitude [m(ft.)] < 5000 m (16404.2 ft.)
Storage temperature [°C(°F)] -40°C to +70°C (-40°F to +158°F)
Overtemperature alarm Supported
Translation
Favorite
Download
Update Date：2025-08-13
Document ID：EDOC1100041787
Views：2922069
Downloads：27571
Average rating：4.0Points

Related Documents

Digital Signature File

digtal sigature tool